Version: dev

NoahSnowEnergy

The snow-pack surface energy balance of WRF's unified Noah land-surface model, SUBROUTINE SNOPAC of phys/module_sf_noahlsm.F (WRF 4.8, sf_surface_physics = 2): the linearised snow-surface temperature t12, the branch it selects, the skin temperature and ground heat flux that follow, and the melt rate. THE CLOSURE. SNOPAC solves the surface balance over a slab of thickness dtot = snowh + half the top soil layer, treating the snow and that half-layer as one conductive path of conductivity df1. Writing the balance about the air temperature gives t12 = (sfctmp + t12a + t12b)/denom, where t12a carries the radiative and turbulent forcing per unit rch and per unit rr, t12b the conduction from the top soil layer, and denom = 1 + df1/(dtot rr rch) the strength of that conduction relative to the atmospheric coupling. t12 is the temperature the snow surface WOULD reach with no melting. THE BRANCH. If t12 is at or below freezing the pack simply cools: the skin temperature is t12 itself, nothing melts, and the pack loses only what sublimates. If t12 is above freezing the surface is pinned near freezing instead -- t1 is a cover-weighted blend of the freezing point and t12, with the weight max(0.01, sncovr^2), so a thin pack lets the surface run warm while a full one holds it at 273.15 K -- and the energy the balance cannot dispose of becomes melt. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER, not after, and that distinction is the same one FORTRAN_BUGS N97 forced for the frozen-soil sink. flx3 is the residual of the balance evaluated at the blended skin temperature, floored at zero, and the melt rate is ex = flx3/(rho_w lsubf). That rate is a rate: it needs no differencing and has no dt dependence. WRF then applies TWO projections on top of it, both explicitly finite-dt, and this component reports each as an indicator rather than folding it into the rate. `pack_exhausted` is WRF's `esd - esnow2 <= esdmin` test, which zeroes the whole melt block when a step's sublimation would finish the pack; esnow2 is a sublimation AMOUNT, esnow1 dt, so the test is dt-dependent and in the dt -> 0 limit reduces to esd <= esdmin. `melt_limited` is WRF's `esd - snomlt < esdmin` test, which rewrites ex as esd/dt when a step's melt would overshoot the remaining pack -- a rate manufactured from an amount, and the clearest finite-dt artefact in the routine. A consumer integrating ex must apply both as projections of the state after its step, exactly as it would the supersaturation redistribution in soil_moisture.esm; neither belongs in a tendency. NOT TRANSCRIBED: the whole UA_PHYS branch (flx4, etpn and the canopy-shading adjustment to the melt energy), which is off in every reference run; SNOWPACK's compaction of the pack, which is a separate routine and a separate component; and EVAPO itself, whose snow-free evapotranspiration enters as the input eta_nosnow (evapotranspiration.esm's eta_kinematic). THE EVAPORATION SPLIT (module_sf_noahlsm.F:3136-3203) is transcribed: where PENMAN's etp is downward (etp <= 0) SNOPAC first rescales it over a stable surface -- ribb >= 0.1 and fdown > 150 W/m^2 -- to (min(etp (1 - ribb), 0) sncovr/0.98 + etp (0.98 - sncovr))/0.98, then books the whole of it as frost, dew = -0.001 etp_adj, and charges the balance etanrg = etp_adj ((1 - sncovr) lsubc + sncovr lsubs); where it is upward the snow-covered fraction sublimates at esnow = etp sncovr, the bare fraction evaporates at etns = (1 - sncovr) eta_nosnow, and etanrg = esnow lsubs + etns lsubc. The pack projections read esnow2_rate, which is ESNOW1 on the upward branch and the (negative) frost rate on the downward one, as SNOPAC's ESNOW2 is. Consumer-supplied column fields are rewrite-target ops `input_<name>` lowered by the consumer, in the inline tests through per-test expression_template_imports libraries generated by tools/fill_tests.py.

.esm schema
1.1.0
Source
components/land_surface/noah/snow_energy.esm

Description

The snow-pack surface energy balance of WRF’s unified Noah land-surface model, SUBROUTINE SNOPAC of phys/module_sf_noahlsm.F (WRF 4.8, sf_surface_physics = 2): the linearised snow-surface temperature t12, the branch it selects, the skin temperature and ground heat flux that follow, and the melt rate. THE CLOSURE. SNOPAC solves the surface balance over a slab of thickness dtot = snowh + half the top soil layer, treating the snow and that half-layer as one conductive path of conductivity df1. Writing the balance about the air temperature gives t12 = (sfctmp + t12a + t12b)/denom, where t12a carries the radiative and turbulent forcing per unit rch and per unit rr, t12b the conduction from the top soil layer, and denom = 1 + df1/(dtot rr rch) the strength of that conduction relative to the atmospheric coupling. t12 is the temperature the snow surface WOULD reach with no melting. THE BRANCH. If t12 is at or below freezing the pack simply cools: the skin temperature is t12 itself, nothing melts, and the pack loses only what sublimates. If t12 is above freezing the surface is pinned near freezing instead – t1 is a cover-weighted blend of the freezing point and t12, with the weight max(0.01, sncovr^2), so a thin pack lets the surface run warm while a full one holds it at 273.15 K – and the energy the balance cannot dispose of becomes melt. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER, not after, and that distinction is the same one FORTRAN_BUGS N97 forced for the frozen-soil sink. flx3 is the residual of the balance evaluated at the blended skin temperature, floored at zero, and the melt rate is ex = flx3/(rho_w lsubf). That rate is a rate: it needs no differencing and has no dt dependence. WRF then applies TWO projections on top of it, both explicitly finite-dt, and this component reports each as an indicator rather than folding it into the rate. pack_exhausted is WRF’s esd - esnow2 <= esdmin test, which zeroes the whole melt block when a step’s sublimation would finish the pack; esnow2 is a sublimation AMOUNT, esnow1 dt, so the test is dt-dependent and in the dt -> 0 limit reduces to esd <= esdmin. melt_limited is WRF’s esd - snomlt < esdmin test, which rewrites ex as esd/dt when a step’s melt would overshoot the remaining pack – a rate manufactured from an amount, and the clearest finite-dt artefact in the routine. A consumer integrating ex must apply both as projections of the state after its step, exactly as it would the supersaturation redistribution in soil_moisture.esm; neither belongs in a tendency. NOT TRANSCRIBED: the whole UA_PHYS branch (flx4, etpn and the canopy-shading adjustment to the melt energy), which is off in every reference run; SNOWPACK’s compaction of the pack, which is a separate routine and a separate component; and EVAPO itself, whose snow-free evapotranspiration enters as the input eta_nosnow (evapotranspiration.esm’s eta_kinematic). THE EVAPORATION SPLIT (module_sf_noahlsm.F:3136-3203) is transcribed: where PENMAN’s etp is downward (etp <= 0) SNOPAC first rescales it over a stable surface – ribb >= 0.1 and fdown > 150 W/m^2 – to (min(etp (1 - ribb), 0) sncovr/0.98 + etp (0.98 - sncovr))/0.98, then books the whole of it as frost, dew = -0.001 etp_adj, and charges the balance etanrg = etp_adj ((1 - sncovr) lsubc + sncovr lsubs); where it is upward the snow-covered fraction sublimates at esnow = etp sncovr, the bare fraction evaporates at etns = (1 - sncovr) eta_nosnow, and etanrg = esnow lsubs + etns lsubc. The pack projections read esnow2_rate, which is ESNOW1 on the upward branch and the (negative) frost rate on the downward one, as SNOPAC’s ESNOW2 is. Consumer-supplied column fields are rewrite-target ops input_<name> lowered by the consumer, in the inline tests through per-test expression_template_imports libraries generated by tools/fill_tests.py.

Reference

  • Koren, V., et al. (1999). A parameterization of snowpack and frozen ground intended for NCEP weather and climate models. J. Geophys. Res., 104(D16), 19569-19585.
  • Ek, M. B., et al. (2003). Implementation of Noah land surface model advances in the NCEP operational mesoscale Eta model. J. Geophys. Res., 108(D22), 8851.
  • Livneh, B., et al. (2010). Noah LSM snow model diagnostics and enhancements. J. Hydrometeor., 11, 721-738.
  • wrf-model/WRF v4.8.0 phys/module_sf_noahlsm.F SUBROUTINE SNOPAC lines 3070-3400 (cold-season reference run instrumented in ctessum-claude/WRF branch earthsciml-instrumented-noahcold, commit 4695cee3).

Parameters

NameUnitsDefaultDescription
sfctmpK265.0Air temperature at the lowest model level.
th2K265.0Potential temperature at the lowest model level referenced to the surface pressure.
t1_inK265.0Skin temperature carried in from the previous step. Read ONLY by flx1, the sensible-heat content of falling precipitation, which WRF evaluates before the new skin temperature exists.
rchW/(m^2*K)10.0Bulk heat-transfer coefficient in energy units, from the Penman component.
rr12.0Resistance ratio, from the Penman component.
t24K^44900000000.0Fourth power of the AIR temperature, from the Penman component: the linearisation point of the surface emission in t12a.
fdownW/m^2300.0Total absorbed downward radiation at the surface, solnet + lwdn.
flx2W/m^20.0Latent heat released by freezing rain on impact, from the Penman component.
emissi10.95Surface emissivity, from the snow-cover component.
df1W/(m*K)0.2Conductivity of the combined snow-and-soil path, WRF’s DF1 after SFLX has blended the snow conductivity into the soil value by snow-cover fraction.
snowhm0.3Physical depth of the pack.
sncovr10.98Snow-cover fraction, from the snow-cover component.
prcpkg/(m^2*s)0.0Precipitation rate reaching the surface.
snowing10.0Indicator (1/0) for WRF’s SNOWNG, which selects the ice rather than the liquid heat capacity for falling precipitation.
esdm0.06Snow water equivalent of the pack entering the step, WRF’s ESD. Read only by the two finite-dt projections.
dt_packs60.0Sub-step over which the two pack projections are evaluated. A parameter of the projections, not the integrator’s step, and it does NOT enter the melt rate: prescribe it in the mounting document.
etpkg/(m^2*s)0.0Potential evaporation SNOPAC receives, WRF’s ETP straight out of PENMAN (potential_evaporation.esm’s etp, kinematic: epsca rch/lvs), BEFORE SNOPAC’s frost adjustment. Negative means frost (deposition).
ribb10.0Bulk Richardson number of the surface layer, WRF’s RIBB (passed down from the surface-layer scheme). Read only by the frost adjustment.
eta_nosnowkg/(m^2*s)0.0EVAPO’s total evapotranspiration for the full potential etp, as if the cell were snow-free: evapotranspiration.esm’s eta_kinematic when that component is driven with etp lvh2o. SNOPAC calls EVAPO with the unweighted ETP1 and only afterwards multiplies its result by (1 - sncovr), which this component does. Read only where etp > 0.

Observed

NameUnitsDefaultDescription
zemSoil layer interface DEPTHS below the surface, positive downward, ze[1] = 0.
stcKSoil temperature of each layer, WRF’s STC. Only the top layer is read, through the conduction term.
dsoilmHalf the top soil layer, 0.5 ze[2], the soil part of the conductive path.
dtotmTotal conductive path, snowh + dsoil: the pack plus the upper half of the top soil layer, treated as one slab.
denom11 + df1/(dtot rr rch): how strongly the soil below holds the snow surface, relative to the atmosphere above. It tends to 1 for a deep pack, where the surface decouples from the soil.
flx1W/m^2Sensible heat carried by falling precipitation, cpice prcp (t1_in - sfctmp) when it is snowing and cph2o prcp (t1_in - sfctmp) for rain, zero with no precipitation. Evaluated at the INCOMING skin temperature.
frost_adjusted11 where SNOPAC rescales a downward potential evaporation, ‘IF (ETP <= 0) … IF ((RIBB >= 0.1) .AND. (FDOWN > 150.0))’ (module_sf_noahlsm.F:3139), else 0.
etp_adjkg/(m^2*s)Potential evaporation after SNOPAC’s frost adjustment: where frost_adjusted, (min(etp (1 - ribb), 0) sncovr/0.98 + etp (0.98 - sncovr))/0.98, which damps deposition onto the snow-covered part of a stable (ribb >= 0.1) surface; etp itself otherwise. SNOPAC writes it back into ETP, so it is also the etp SFLX reports.
etnskg/(m^2*s)Evaporation from the snow-free fraction, WRF’s ETNS: eta_nosnow (1 - sncovr) where etp > 0 and sncovr < 1, else 0.
esnowkg/(m^2*s)Sublimation from the snow-covered fraction, WRF’s ESNOW (kinematic): etp sncovr where etp > 0, else 0 (frost is carried by dew instead).
esnow_ratem/sESNOW as a water velocity, WRF’s ESNOW1 = 0.001 ESNOW; zero on the frost branch.
dewm/sFrost deposition rate, WRF’s DEW = -0.001 etp_adj where etp <= 0, else 0.
esnow2_ratem/sThe rate whose step amount SNOPAC subtracts from the pack, ESNOW2/dt: ESNOW1 where etp > 0, and 0.001 etp_adj (negative, i.e. frost adds) where etp <= 0. Read only by the two pack projections.
etanrgW/m^2Total latent-heat flux the balance must dispose of, WRF’s ETANRG: esnow lsubs + etns lsubc where etp > 0 (sublimation at the latent heat of SUBLIMATION plus bare-fraction evaporation at that of vaporisation, lsubc = lvh2o), and etp_adj ((1 - sncovr) lsubc + sncovr lsubs) on the frost branch.
t12aKThe forcing term of the closure: net radiation at the linearisation temperature, less the precipitation and freezing-rain heat and the latent flux, expressed as a temperature through rch and rr, plus the air’s potential-temperature offset.
t12bKThe conduction term, df1 stc[1]/(dtot rr rch): the top soil layer pulling the snow surface towards itself.
t12KSnow-surface temperature with NO melting, (sfctmp + t12a + t12b)/denom. Its position relative to the freezing point is what selects the branch.
melting1Indicator, 1 where t12 exceeds the freezing point and SNOPAC takes its melt block. 29 of the 84 cold-season reference steps; 38 take the sub-freezing block.
cover_weight1max(0.01, sncovr^2), the weight with which the melting surface is pinned to the freezing point. The floor of 0.01 keeps a vanishing pack from decoupling entirely.
t1KSkin temperature: t12 itself on the sub-freezing branch, and on the melt branch the cover-weighted blend of the freezing point and t12, so a full pack holds the surface at 273.15 K while a thin one lets it run warm.
ssoilW/m^2Ground heat flux through the combined path, df1 (t1 - stc[1])/dtot, positive downward into the soil. Note this is WRF’s pre-flip sign convention inside SNOPAC; SFLX negates it before reporting.
sehW/m^2Sensible heat flux at the melting surface, rch (t1 - th2). Assigned only inside the melt block in WRF, and meaningful only there.
t14K^4Fourth power of the SKIN temperature, used for the emission in the melt residual – unlike t24 in t12a, which uses the air temperature.
flx3_rawW/m^2Residual of the energy balance at the melting surface, fdown - flx1 - flx2 - emissi sigma t14 - ssoil - seh - etanrg, before it is floored.
flx3W/m^2The melt energy, max(flx3_raw, 0) on the melt branch and exactly zero on the sub-freezing branch.
exm/sMelt rate as a water velocity, flx3/(rho_water lsubf). This is a RATE and is what a consumer integrates; it carries no dt dependence and needs no differencing, which is why it is referenced directly rather than through the snow amount.
pack_exhausted1Indicator for WRF’s esd - esnow2_rate dt_pack <= esdmin test, which zeroes the entire melt block when a step’s sublimation would finish the pack. A PROJECTION of the state, dt-dependent by construction, reported rather than applied; in the dt -> 0 limit it reduces to esd <= esdmin.
melt_limited1Indicator for WRF’s esd - esnow2_rate dt_pack - ex dt_pack < esdmin test, which rewrites the melt rate as esd/dt_pack when a step’s melt would overshoot the remaining pack. A rate manufactured from an amount, and the clearest finite-dt artefact in the routine: a PROJECTION, reported rather than applied. UNTESTED against the reference set’s melt branch, which never reaches it at the replay step size.

Observed expressions

$$ ze = \mathrm{input_ze}\left(\right) $$

Soil layer interface DEPTHS below the surface, positive downward, ze[1] = 0.

$$ stc = \mathrm{input_stc}\left(\right) $$

Soil temperature of each layer, WRF’s STC. Only the top layer is read, through the conduction term.

$$ dsoil = 0.5 \cdot \mathrm{index}\left(ze, 2\right) $$

Half the top soil layer, 0.5 ze[2], the soil part of the conductive path.

$$ dtot = snowh + dsoil $$

Total conductive path, snowh + dsoil: the pack plus the upper half of the top soil layer, treated as one slab.

$$ denom = 1.0 + \frac{df1}{dtot \cdot rr \cdot rch} $$

1 + df1/(dtot rr rch): how strongly the soil below holds the snow surface, relative to the atmosphere above. It tends to 1 for a deep pack, where the surface decouples from the soil.

$$ flx1 = \mathrm{ifelse}\left(snowing = 1.0, par.cpice \cdot prcp \cdot \left(t1_{in} - sfctmp\right), \mathrm{ifelse}\left(\mathrm{>}\left(prcp, 0.0\right), par.cph2o \cdot prcp \cdot \left(t1_{in} - sfctmp\right), 0.0\right)\right) $$

Sensible heat carried by falling precipitation, cpice prcp (t1_in - sfctmp) when it is snowing and cph2o prcp (t1_in - sfctmp) for rain, zero with no precipitation. Evaluated at the INCOMING skin temperature.

$$ frost_{adjusted} = \mathrm{ifelse}\left(\mathrm{and}\left(\mathrm{and}\left(\mathrm{<=}\left(etp, 0.0\right), \mathrm{>=}\left(ribb, 0.1\right)\right), \mathrm{>}\left(fdown, 150.0\right)\right), 1.0, 0.0\right) $$

1 where SNOPAC rescales a downward potential evaporation, ‘IF (ETP <= 0) … IF ((RIBB >= 0.1) .AND. (FDOWN > 150.0))’ (module_sf_noahlsm.F:3139), else 0.

$$ etp_{adj} = \mathrm{ifelse}\left(frost_{adjusted} = 1.0, \frac{\frac{\mathrm{min}\left(etp \cdot \left(1.0 - ribb\right), 0.0\right) \cdot sncovr}{0.98} + etp \cdot \left(0.98 - sncovr\right)}{0.98}, etp\right) $$

Potential evaporation after SNOPAC’s frost adjustment: where frost_adjusted, (min(etp (1 - ribb), 0) sncovr/0.98 + etp (0.98 - sncovr))/0.98, which damps deposition onto the snow-covered part of a stable (ribb >= 0.1) surface; etp itself otherwise. SNOPAC writes it back into ETP, so it is also the etp SFLX reports.

$$ etns = \mathrm{ifelse}\left(\mathrm{and}\left(\mathrm{>}\left(etp, 0.0\right), \mathrm{<}\left(sncovr, 1.0\right)\right), eta_{nosnow} \cdot \left(1.0 - sncovr\right), 0.0\right) $$

Evaporation from the snow-free fraction, WRF’s ETNS: eta_nosnow (1 - sncovr) where etp > 0 and sncovr < 1, else 0.

$$ esnow = \mathrm{ifelse}\left(\mathrm{>}\left(etp, 0.0\right), etp \cdot sncovr, 0.0\right) $$

Sublimation from the snow-covered fraction, WRF’s ESNOW (kinematic): etp sncovr where etp > 0, else 0 (frost is carried by dew instead).

$$ esnow_{rate} = \frac{esnow}{par.rho_{water}} $$

ESNOW as a water velocity, WRF’s ESNOW1 = 0.001 ESNOW; zero on the frost branch.

$$ dew = \mathrm{ifelse}\left(\mathrm{<=}\left(etp, 0.0\right), \frac{0.0 - etp_{adj}}{par.rho_{water}}, 0.0\right) $$

Frost deposition rate, WRF’s DEW = -0.001 etp_adj where etp <= 0, else 0.

$$ esnow2_{rate} = \mathrm{ifelse}\left(\mathrm{>}\left(etp, 0.0\right), esnow_{rate}, \frac{etp_{adj}}{par.rho_{water}}\right) $$

The rate whose step amount SNOPAC subtracts from the pack, ESNOW2/dt: ESNOW1 where etp > 0, and 0.001 etp_adj (negative, i.e. frost adds) where etp <= 0. Read only by the two pack projections.

$$ etanrg = \mathrm{ifelse}\left(\mathrm{>}\left(etp, 0.0\right), esnow \cdot par.lsubs + etns \cdot par.lvh2o, etp_{adj} \cdot \left(\left(1.0 - sncovr\right) \cdot par.lvh2o + sncovr \cdot par.lsubs\right)\right) $$

Total latent-heat flux the balance must dispose of, WRF’s ETANRG: esnow lsubs + etns lsubc where etp > 0 (sublimation at the latent heat of SUBLIMATION plus bare-fraction evaporation at that of vaporisation, lsubc = lvh2o), and etp_adj ((1 - sncovr) lsubc + sncovr lsubs) on the frost branch.

$$ t12a = \frac{\frac{fdown - flx1 - flx2 - emissi \cdot par.sigma \cdot t24}{rch} + th2 - sfctmp - \frac{etanrg}{rch}}{rr} $$

The forcing term of the closure: net radiation at the linearisation temperature, less the precipitation and freezing-rain heat and the latent flux, expressed as a temperature through rch and rr, plus the air’s potential-temperature offset.

$$ t12b = \frac{df1 \cdot \mathrm{index}\left(stc, 1\right)}{dtot \cdot rr \cdot rch} $$

The conduction term, df1 stc[1]/(dtot rr rch): the top soil layer pulling the snow surface towards itself.

$$ t12 = \frac{sfctmp + t12a + t12b}{denom} $$

Snow-surface temperature with NO melting, (sfctmp + t12a + t12b)/denom. Its position relative to the freezing point is what selects the branch.

$$ melting = \mathrm{ifelse}\left(\mathrm{>}\left(t12, par.t0\right), 1.0, 0.0\right) $$

Indicator, 1 where t12 exceeds the freezing point and SNOPAC takes its melt block. 29 of the 84 cold-season reference steps; 38 take the sub-freezing block.

$$ cover_{weight} = \mathrm{max}\left(0.01, sncovr^{2.0}\right) $$

max(0.01, sncovr^2), the weight with which the melting surface is pinned to the freezing point. The floor of 0.01 keeps a vanishing pack from decoupling entirely.

$$ t1 = \mathrm{ifelse}\left(melting = 1.0, par.t0 \cdot cover_{weight} + t12 \cdot \left(1.0 - cover_{weight}\right), t12\right) $$

Skin temperature: t12 itself on the sub-freezing branch, and on the melt branch the cover-weighted blend of the freezing point and t12, so a full pack holds the surface at 273.15 K while a thin one lets it run warm.

$$ ssoil = \frac{df1 \cdot \left(t1 - \mathrm{index}\left(stc, 1\right)\right)}{dtot} $$

Ground heat flux through the combined path, df1 (t1 - stc[1])/dtot, positive downward into the soil. Note this is WRF’s pre-flip sign convention inside SNOPAC; SFLX negates it before reporting.

$$ seh = rch \cdot \left(t1 - th2\right) $$

Sensible heat flux at the melting surface, rch (t1 - th2). Assigned only inside the melt block in WRF, and meaningful only there.

$$ t14 = t1^{4.0} $$

Fourth power of the SKIN temperature, used for the emission in the melt residual – unlike t24 in t12a, which uses the air temperature.

$$ flx3_{raw} = fdown - flx1 - flx2 - emissi \cdot par.sigma \cdot t14 - ssoil - seh - etanrg $$

Residual of the energy balance at the melting surface, fdown - flx1 - flx2 - emissi sigma t14 - ssoil - seh - etanrg, before it is floored.

$$ flx3 = \mathrm{ifelse}\left(melting = 1.0, \mathrm{max}\left(flx3_{raw}, 0.0\right), 0.0\right) $$

The melt energy, max(flx3_raw, 0) on the melt branch and exactly zero on the sub-freezing branch.

$$ ex = \frac{flx3}{par.rho_{water} \cdot par.lsubf} $$

Melt rate as a water velocity, flx3/(rho_water lsubf). This is a RATE and is what a consumer integrates; it carries no dt dependence and needs no differencing, which is why it is referenced directly rather than through the snow amount.

$$ pack_{exhausted} = \mathrm{ifelse}\left(\mathrm{<=}\left(esd - esnow2_{rate} \cdot dt_{pack}, 1 \times 10^{-6}\right), 1.0, 0.0\right) $$

Indicator for WRF’s esd - esnow2_rate dt_pack <= esdmin test, which zeroes the entire melt block when a step’s sublimation would finish the pack. A PROJECTION of the state, dt-dependent by construction, reported rather than applied; in the dt -> 0 limit it reduces to esd <= esdmin.

$$ melt_{limited} = \mathrm{ifelse}\left(\mathrm{and}\left(pack_{exhausted} = 0.0, \mathrm{<}\left(esd - esnow2_{rate} \cdot dt_{pack} - ex \cdot dt_{pack}, 1 \times 10^{-6}\right)\right), 1.0, 0.0\right) $$

Indicator for WRF’s esd - esnow2_rate dt_pack - ex dt_pack < esdmin test, which rewrites the melt rate as esd/dt_pack when a step’s melt would overshoot the remaining pack. A rate manufactured from an amount, and the clearest finite-dt artefact in the routine: a PROJECTION, reported rather than applied. UNTESTED against the reference set’s melt branch, which never reaches it at the replay step size.

Raw .esm

Raw .esm JSON (this component)
{
  "expression_template_imports": [
    {
      "ref": "${ESD_ROOT}/grids/column_nonuniform_1d/grid.esm",
      "bindings": {
        "NLEV": "NLEV"
      }
    }
  ],
  "subsystems": {
    "par": {
      "ref": "./noah_parameters.esm"
    }
  },
  "variables": {
    "ze": {
      "type": "unknown",
      "units": "m",
      "shape": [
        "lev_nodes"
      ],
      "description": "Soil layer interface DEPTHS below the surface, positive downward, ze[1] = 0."
    },
    "stc": {
      "type": "unknown",
      "units": "K",
      "shape": [
        "lev"
      ],
      "description": "Soil temperature of each layer, WRF's STC. Only the top layer is read, through the conduction term."
    },
    "sfctmp": {
      "type": "parameter",
      "units": "K",
      "default": 265.0,
      "description": "Air temperature at the lowest model level."
    },
    "th2": {
      "type": "parameter",
      "units": "K",
      "default": 265.0,
      "description": "Potential temperature at the lowest model level referenced to the surface pressure."
    },
    "t1_in": {
      "type": "parameter",
      "units": "K",
      "default": 265.0,
      "description": "Skin temperature carried in from the previous step. Read ONLY by flx1, the sensible-heat content of falling precipitation, which WRF evaluates before the new skin temperature exists."
    },
    "rch": {
      "type": "parameter",
      "units": "W/(m^2*K)",
      "default": 10.0,
      "description": "Bulk heat-transfer coefficient in energy units, from the Penman component."
    },
    "rr": {
      "type": "parameter",
      "units": "1",
      "default": 2.0,
      "description": "Resistance ratio, from the Penman component."
    },
    "t24": {
      "type": "parameter",
      "units": "K^4",
      "default": 4900000000.0,
      "description": "Fourth power of the AIR temperature, from the Penman component: the linearisation point of the surface emission in t12a."
    },
    "fdown": {
      "type": "parameter",
      "units": "W/m^2",
      "default": 300.0,
      "description": "Total absorbed downward radiation at the surface, solnet + lwdn."
    },
    "flx2": {
      "type": "parameter",
      "units": "W/m^2",
      "default": 0.0,
      "description": "Latent heat released by freezing rain on impact, from the Penman component."
    },
    "emissi": {
      "type": "parameter",
      "units": "1",
      "default": 0.95,
      "description": "Surface emissivity, from the snow-cover component."
    },
    "df1": {
      "type": "parameter",
      "units": "W/(m*K)",
      "default": 0.2,
      "description": "Conductivity of the combined snow-and-soil path, WRF's DF1 after SFLX has blended the snow conductivity into the soil value by snow-cover fraction."
    },
    "snowh": {
      "type": "parameter",
      "units": "m",
      "default": 0.3,
      "description": "Physical depth of the pack."
    },
    "sncovr": {
      "type": "parameter",
      "units": "1",
      "default": 0.98,
      "description": "Snow-cover fraction, from the snow-cover component."
    },
    "prcp": {
      "type": "parameter",
      "units": "kg/(m^2*s)",
      "default": 0.0,
      "description": "Precipitation rate reaching the surface."
    },
    "snowing": {
      "type": "parameter",
      "units": "1",
      "default": 0.0,
      "description": "Indicator (1/0) for WRF's SNOWNG, which selects the ice rather than the liquid heat capacity for falling precipitation."
    },
    "esd": {
      "type": "parameter",
      "units": "m",
      "default": 0.06,
      "description": "Snow water equivalent of the pack entering the step, WRF's ESD. Read only by the two finite-dt projections."
    },
    "dt_pack": {
      "type": "parameter",
      "units": "s",
      "default": 60.0,
      "description": "Sub-step over which the two pack projections are evaluated. A parameter of the projections, not the integrator's step, and it does NOT enter the melt rate: prescribe it in the mounting document."
    },
    "etp": {
      "type": "parameter",
      "units": "kg/(m^2*s)",
      "default": 0.0,
      "description": "Potential evaporation SNOPAC receives, WRF's ETP straight out of PENMAN (potential_evaporation.esm's etp, kinematic: epsca rch/lvs), BEFORE SNOPAC's frost adjustment. Negative means frost (deposition)."
    },
    "ribb": {
      "type": "parameter",
      "units": "1",
      "default": 0.0,
      "description": "Bulk Richardson number of the surface layer, WRF's RIBB (passed down from the surface-layer scheme). Read only by the frost adjustment."
    },
    "eta_nosnow": {
      "type": "parameter",
      "units": "kg/(m^2*s)",
      "default": 0.0,
      "description": "EVAPO's total evapotranspiration for the full potential etp, as if the cell were snow-free: evapotranspiration.esm's eta_kinematic when that component is driven with etp lvh2o. SNOPAC calls EVAPO with the unweighted ETP1 and only afterwards multiplies its result by (1 - sncovr), which this component does. Read only where etp > 0."
    },
    "dsoil": {
      "type": "unknown",
      "units": "m",
      "description": "Half the top soil layer, 0.5 ze[2], the soil part of the conductive path."
    },
    "dtot": {
      "type": "unknown",
      "units": "m",
      "description": "Total conductive path, snowh + dsoil: the pack plus the upper half of the top soil layer, treated as one slab."
    },
    "denom": {
      "type": "unknown",
      "units": "1",
      "description": "1 + df1/(dtot rr rch): how strongly the soil below holds the snow surface, relative to the atmosphere above. It tends to 1 for a deep pack, where the surface decouples from the soil."
    },
    "flx1": {
      "type": "unknown",
      "units": "W/m^2",
      "description": "Sensible heat carried by falling precipitation, cpice prcp (t1_in - sfctmp) when it is snowing and cph2o prcp (t1_in - sfctmp) for rain, zero with no precipitation. Evaluated at the INCOMING skin temperature."
    },
    "frost_adjusted": {
      "type": "unknown",
      "units": "1",
      "description": "1 where SNOPAC rescales a downward potential evaporation, 'IF (ETP <= 0) ... IF ((RIBB >= 0.1) .AND. (FDOWN > 150.0))' (module_sf_noahlsm.F:3139), else 0."
    },
    "etp_adj": {
      "type": "unknown",
      "units": "kg/(m^2*s)",
      "description": "Potential evaporation after SNOPAC's frost adjustment: where frost_adjusted, (min(etp (1 - ribb), 0) sncovr/0.98 + etp (0.98 - sncovr))/0.98, which damps deposition onto the snow-covered part of a stable (ribb >= 0.1) surface; etp itself otherwise. SNOPAC writes it back into ETP, so it is also the etp SFLX reports."
    },
    "etns": {
      "type": "unknown",
      "units": "kg/(m^2*s)",
      "description": "Evaporation from the snow-free fraction, WRF's ETNS: eta_nosnow (1 - sncovr) where etp > 0 and sncovr < 1, else 0."
    },
    "esnow": {
      "type": "unknown",
      "units": "kg/(m^2*s)",
      "description": "Sublimation from the snow-covered fraction, WRF's ESNOW (kinematic): etp sncovr where etp > 0, else 0 (frost is carried by dew instead)."
    },
    "esnow_rate": {
      "type": "unknown",
      "units": "m/s",
      "description": "ESNOW as a water velocity, WRF's ESNOW1 = 0.001 ESNOW; zero on the frost branch."
    },
    "dew": {
      "type": "unknown",
      "units": "m/s",
      "description": "Frost deposition rate, WRF's DEW = -0.001 etp_adj where etp <= 0, else 0."
    },
    "esnow2_rate": {
      "type": "unknown",
      "units": "m/s",
      "description": "The rate whose step amount SNOPAC subtracts from the pack, ESNOW2/dt: ESNOW1 where etp > 0, and 0.001 etp_adj (negative, i.e. frost adds) where etp <= 0. Read only by the two pack projections."
    },
    "etanrg": {
      "type": "unknown",
      "units": "W/m^2",
      "description": "Total latent-heat flux the balance must dispose of, WRF's ETANRG: esnow lsubs + etns lsubc where etp > 0 (sublimation at the latent heat of SUBLIMATION plus bare-fraction evaporation at that of vaporisation, lsubc = lvh2o), and etp_adj ((1 - sncovr) lsubc + sncovr lsubs) on the frost branch."
    },
    "t12a": {
      "type": "unknown",
      "units": "K",
      "description": "The forcing term of the closure: net radiation at the linearisation temperature, less the precipitation and freezing-rain heat and the latent flux, expressed as a temperature through rch and rr, plus the air's potential-temperature offset."
    },
    "t12b": {
      "type": "unknown",
      "units": "K",
      "description": "The conduction term, df1 stc[1]/(dtot rr rch): the top soil layer pulling the snow surface towards itself."
    },
    "t12": {
      "type": "unknown",
      "units": "K",
      "description": "Snow-surface temperature with NO melting, (sfctmp + t12a + t12b)/denom. Its position relative to the freezing point is what selects the branch."
    },
    "melting": {
      "type": "unknown",
      "units": "1",
      "description": "Indicator, 1 where t12 exceeds the freezing point and SNOPAC takes its melt block. 29 of the 84 cold-season reference steps; 38 take the sub-freezing block."
    },
    "cover_weight": {
      "type": "unknown",
      "units": "1",
      "description": "max(0.01, sncovr^2), the weight with which the melting surface is pinned to the freezing point. The floor of 0.01 keeps a vanishing pack from decoupling entirely."
    },
    "t1": {
      "type": "unknown",
      "units": "K",
      "description": "Skin temperature: t12 itself on the sub-freezing branch, and on the melt branch the cover-weighted blend of the freezing point and t12, so a full pack holds the surface at 273.15 K while a thin one lets it run warm."
    },
    "ssoil": {
      "type": "unknown",
      "units": "W/m^2",
      "description": "Ground heat flux through the combined path, df1 (t1 - stc[1])/dtot, positive downward into the soil. Note this is WRF's pre-flip sign convention inside SNOPAC; SFLX negates it before reporting."
    },
    "seh": {
      "type": "unknown",
      "units": "W/m^2",
      "description": "Sensible heat flux at the melting surface, rch (t1 - th2). Assigned only inside the melt block in WRF, and meaningful only there."
    },
    "t14": {
      "type": "unknown",
      "units": "K^4",
      "description": "Fourth power of the SKIN temperature, used for the emission in the melt residual -- unlike t24 in t12a, which uses the air temperature."
    },
    "flx3_raw": {
      "type": "unknown",
      "units": "W/m^2",
      "description": "Residual of the energy balance at the melting surface, fdown - flx1 - flx2 - emissi sigma t14 - ssoil - seh - etanrg, before it is floored."
    },
    "flx3": {
      "type": "unknown",
      "units": "W/m^2",
      "description": "The melt energy, max(flx3_raw, 0) on the melt branch and exactly zero on the sub-freezing branch."
    },
    "ex": {
      "type": "unknown",
      "units": "m/s",
      "description": "Melt rate as a water velocity, flx3/(rho_water lsubf). This is a RATE and is what a consumer integrates; it carries no dt dependence and needs no differencing, which is why it is referenced directly rather than through the snow amount."
    },
    "pack_exhausted": {
      "type": "unknown",
      "units": "1",
      "description": "Indicator for WRF's esd - esnow2_rate dt_pack <= esdmin test, which zeroes the entire melt block when a step's sublimation would finish the pack. A PROJECTION of the state, dt-dependent by construction, reported rather than applied; in the dt -> 0 limit it reduces to esd <= esdmin."
    },
    "melt_limited": {
      "type": "unknown",
      "units": "1",
      "description": "Indicator for WRF's esd - esnow2_rate dt_pack - ex dt_pack < esdmin test, which rewrites the melt rate as esd/dt_pack when a step's melt would overshoot the remaining pack. A rate manufactured from an amount, and the clearest finite-dt artefact in the routine: a PROJECTION, reported rather than applied. UNTESTED against the reference set's melt branch, which never reaches it at the replay step size."
    }
  },
  "equations": [
    {
      "lhs": "ze",
      "rhs": {
        "op": "input_ze",
        "args": []
      }
    },
    {
      "lhs": "stc",
      "rhs": {
        "op": "input_stc",
        "args": []
      }
    },
    {
      "lhs": "dsoil",
      "rhs": {
        "op": "*",
        "args": [
          0.5,
          {
            "op": "index",
            "args": [
              "ze",
              2
            ]
          }
        ]
      }
    },
    {
      "lhs": "dtot",
      "rhs": {
        "op": "+",
        "args": [
          "snowh",
          "dsoil"
        ]
      }
    },
    {
      "lhs": "denom",
      "rhs": {
        "op": "+",
        "args": [
          1.0,
          {
            "op": "/",
            "args": [
              "df1",
              {
                "op": "*",
                "args": [
                  {
                    "op": "*",
                    "args": [
                      "dtot",
                      "rr"
                    ]
                  },
                  "rch"
                ]
              }
            ]
          }
        ]
      }
    },
    {
      "lhs": "flx1",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "==",
            "args": [
              "snowing",
              1.0
            ]
          },
          {
            "op": "*",
            "args": [
              {
                "op": "*",
                "args": [
                  "par.cpice",
                  "prcp"
                ]
              },
              {
                "op": "-",
                "args": [
                  "t1_in",
                  "sfctmp"
                ]
              }
            ]
          },
          {
            "op": "ifelse",
            "args": [
              {
                "op": ">",
                "args": [
                  "prcp",
                  0.0
                ]
              },
              {
                "op": "*",
                "args": [
                  {
                    "op": "*",
                    "args": [
                      "par.cph2o",
                      "prcp"
                    ]
                  },
                  {
                    "op": "-",
                    "args": [
                      "t1_in",
                      "sfctmp"
                    ]
                  }
                ]
              },
              0.0
            ]
          }
        ]
      }
    },
    {
      "lhs": "frost_adjusted",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "and",
            "args": [
              {
                "op": "and",
                "args": [
                  {
                    "op": "<=",
                    "args": [
                      "etp",
                      0.0
                    ]
                  },
                  {
                    "op": ">=",
                    "args": [
                      "ribb",
                      0.1
                    ]
                  }
                ]
              },
              {
                "op": ">",
                "args": [
                  "fdown",
                  150.0
                ]
              }
            ]
          },
          1.0,
          0.0
        ]
      }
    },
    {
      "lhs": "etp_adj",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "==",
            "args": [
              "frost_adjusted",
              1.0
            ]
          },
          {
            "op": "/",
            "args": [
              {
                "op": "+",
                "args": [
                  {
                    "op": "/",
                    "args": [
                      {
                        "op": "*",
                        "args": [
                          {
                            "op": "min",
                            "args": [
                              {
                                "op": "*",
                                "args": [
                                  "etp",
                                  {
                                    "op": "-",
                                    "args": [
                                      1.0,
                                      "ribb"
                                    ]
                                  }
                                ]
                              },
                              0.0
                            ]
                          },
                          "sncovr"
                        ]
                      },
                      0.98
                    ]
                  },
                  {
                    "op": "*",
                    "args": [
                      "etp",
                      {
                        "op": "-",
                        "args": [
                          0.98,
                          "sncovr"
                        ]
                      }
                    ]
                  }
                ]
              },
              0.98
            ]
          },
          "etp"
        ]
      }
    },
    {
      "lhs": "etns",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "and",
            "args": [
              {
                "op": ">",
                "args": [
                  "etp",
                  0.0
                ]
              },
              {
                "op": "<",
                "args": [
                  "sncovr",
                  1.0
                ]
              }
            ]
          },
          {
            "op": "*",
            "args": [
              "eta_nosnow",
              {
                "op": "-",
                "args": [
                  1.0,
                  "sncovr"
                ]
              }
            ]
          },
          0.0
        ]
      }
    },
    {
      "lhs": "esnow",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": ">",
            "args": [
              "etp",
              0.0
            ]
          },
          {
            "op": "*",
            "args": [
              "etp",
              "sncovr"
            ]
          },
          0.0
        ]
      }
    },
    {
      "lhs": "esnow_rate",
      "rhs": {
        "op": "/",
        "args": [
          "esnow",
          "par.rho_water"
        ]
      }
    },
    {
      "lhs": "dew",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "<=",
            "args": [
              "etp",
              0.0
            ]
          },
          {
            "op": "/",
            "args": [
              {
                "op": "-",
                "args": [
                  0.0,
                  "etp_adj"
                ]
              },
              "par.rho_water"
            ]
          },
          0.0
        ]
      }
    },
    {
      "lhs": "esnow2_rate",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": ">",
            "args": [
              "etp",
              0.0
            ]
          },
          "esnow_rate",
          {
            "op": "/",
            "args": [
              "etp_adj",
              "par.rho_water"
            ]
          }
        ]
      }
    },
    {
      "lhs": "etanrg",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": ">",
            "args": [
              "etp",
              0.0
            ]
          },
          {
            "op": "+",
            "args": [
              {
                "op": "*",
                "args": [
                  "esnow",
                  "par.lsubs"
                ]
              },
              {
                "op": "*",
                "args": [
                  "etns",
                  "par.lvh2o"
                ]
              }
            ]
          },
          {
            "op": "*",
            "args": [
              "etp_adj",
              {
                "op": "+",
                "args": [
                  {
                    "op": "*",
                    "args": [
                      {
                        "op": "-",
                        "args": [
                          1.0,
                          "sncovr"
                        ]
                      },
                      "par.lvh2o"
                    ]
                  },
                  {
                    "op": "*",
                    "args": [
                      "sncovr",
                      "par.lsubs"
                    ]
                  }
                ]
              }
            ]
          }
        ]
      }
    },
    {
      "lhs": "t12a",
      "rhs": {
        "op": "/",
        "args": [
          {
            "op": "-",
            "args": [
              {
                "op": "-",
                "args": [
                  {
                    "op": "+",
                    "args": [
                      {
                        "op": "/",
                        "args": [
                          {
                            "op": "-",
                            "args": [
                              {
                                "op": "-",
                                "args": [
                                  {
                                    "op": "-",
                                    "args": [
                                      "fdown",
                                      "flx1"
                                    ]
                                  },
                                  "flx2"
                                ]
                              },
                              {
                                "op": "*",
                                "args": [
                                  {
                                    "op": "*",
                                    "args": [
                                      "emissi",
                                      "par.sigma"
                                    ]
                                  },
                                  "t24"
                                ]
                              }
                            ]
                          },
                          "rch"
                        ]
                      },
                      "th2"
                    ]
                  },
                  "sfctmp"
                ]
              },
              {
                "op": "/",
                "args": [
                  "etanrg",
                  "rch"
                ]
              }
            ]
          },
          "rr"
        ]
      }
    },
    {
      "lhs": "t12b",
      "rhs": {
        "op": "/",
        "args": [
          {
            "op": "*",
            "args": [
              "df1",
              {
                "op": "index",
                "args": [
                  "stc",
                  1
                ]
              }
            ]
          },
          {
            "op": "*",
            "args": [
              {
                "op": "*",
                "args": [
                  "dtot",
                  "rr"
                ]
              },
              "rch"
            ]
          }
        ]
      }
    },
    {
      "lhs": "t12",
      "rhs": {
        "op": "/",
        "args": [
          {
            "op": "+",
            "args": [
              {
                "op": "+",
                "args": [
                  "sfctmp",
                  "t12a"
                ]
              },
              "t12b"
            ]
          },
          "denom"
        ]
      }
    },
    {
      "lhs": "melting",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": ">",
            "args": [
              "t12",
              "par.t0"
            ]
          },
          1.0,
          0.0
        ]
      }
    },
    {
      "lhs": "cover_weight",
      "rhs": {
        "op": "max",
        "args": [
          0.01,
          {
            "op": "^",
            "args": [
              "sncovr",
              2.0
            ]
          }
        ]
      }
    },
    {
      "lhs": "t1",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "==",
            "args": [
              "melting",
              1.0
            ]
          },
          {
            "op": "+",
            "args": [
              {
                "op": "*",
                "args": [
                  "par.t0",
                  "cover_weight"
                ]
              },
              {
                "op": "*",
                "args": [
                  "t12",
                  {
                    "op": "-",
                    "args": [
                      1.0,
                      "cover_weight"
                    ]
                  }
                ]
              }
            ]
          },
          "t12"
        ]
      }
    },
    {
      "lhs": "ssoil",
      "rhs": {
        "op": "/",
        "args": [
          {
            "op": "*",
            "args": [
              "df1",
              {
                "op": "-",
                "args": [
                  "t1",
                  {
                    "op": "index",
                    "args": [
                      "stc",
                      1
                    ]
                  }
                ]
              }
            ]
          },
          "dtot"
        ]
      }
    },
    {
      "lhs": "seh",
      "rhs": {
        "op": "*",
        "args": [
          "rch",
          {
            "op": "-",
            "args": [
              "t1",
              "th2"
            ]
          }
        ]
      }
    },
    {
      "lhs": "t14",
      "rhs": {
        "op": "^",
        "args": [
          "t1",
          4.0
        ]
      }
    },
    {
      "lhs": "flx3_raw",
      "rhs": {
        "op": "-",
        "args": [
          {
            "op": "-",
            "args": [
              {
                "op": "-",
                "args": [
                  {
                    "op": "-",
                    "args": [
                      {
                        "op": "-",
                        "args": [
                          {
                            "op": "-",
                            "args": [
                              "fdown",
                              "flx1"
                            ]
                          },
                          "flx2"
                        ]
                      },
                      {
                        "op": "*",
                        "args": [
                          {
                            "op": "*",
                            "args": [
                              "emissi",
                              "par.sigma"
                            ]
                          },
                          "t14"
                        ]
                      }
                    ]
                  },
                  "ssoil"
                ]
              },
              "seh"
            ]
          },
          "etanrg"
        ]
      }
    },
    {
      "lhs": "flx3",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "==",
            "args": [
              "melting",
              1.0
            ]
          },
          {
            "op": "max",
            "args": [
              "flx3_raw",
              0.0
            ]
          },
          0.0
        ]
      }
    },
    {
      "lhs": "ex",
      "rhs": {
        "op": "/",
        "args": [
          "flx3",
          {
            "op": "*",
            "args": [
              "par.rho_water",
              "par.lsubf"
            ]
          }
        ]
      }
    },
    {
      "lhs": "pack_exhausted",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "<=",
            "args": [
              {
                "op": "-",
                "args": [
                  "esd",
                  {
                    "op": "*",
                    "args": [
                      "esnow2_rate",
                      "dt_pack"
                    ]
                  }
                ]
              },
              1e-06
            ]
          },
          1.0,
          0.0
        ]
      }
    },
    {
      "lhs": "melt_limited",
      "rhs": {
        "op": "ifelse",
        "args": [
          {
            "op": "and",
            "args": [
              {
                "op": "==",
                "args": [
                  "pack_exhausted",
                  0.0
                ]
              },
              {
                "op": "<",
                "args": [
                  {
                    "op": "-",
                    "args": [
                      {
                        "op": "-",
                        "args": [
                          "esd",
                          {
                            "op": "*",
                            "args": [
                              "esnow2_rate",
                              "dt_pack"
                            ]
                          }
                        ]
                      },
                      {
                        "op": "*",
                        "args": [
                          "ex",
                          "dt_pack"
                        ]
                      }
                    ]
                  },
                  1e-06
                ]
              }
            ]
          },
          1.0,
          0.0
        ]
      }
    }
  ],
  "tests": [
    {
      "id": "cold_caseA_step101",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 101 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.4576721191406,
        "th2": 264.73040771484375,
        "t1_in": 264.0019226074219,
        "rch": 6.723323469080783,
        "rr": 1.6287407254906414,
        "t24": 4891304309.311497,
        "fdown": 271.76440429769985,
        "flx2": 0.0,
        "emissi": 0.9842905571522402,
        "df1": 0.48983907943929916,
        "snowh": 0.003943329211324453,
        "sncovr": 0.020270196083057135,
        "prcp": 4.892708238912746e-05,
        "snowing": 1.0,
        "esd": 0.00030612968844597697,
        "etp": -4.5585293790906753e-07,
        "ribb": 0.06223485991358757,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A101_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.0539433299570185,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.8292389937880804,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.046960628171654584,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.165109274237481,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 218.29111689329136,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 263.99715943438696,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 263.99715943438696,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 6.850905008954654,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -1.1431282328661714,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -4.558529379090676e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 4.5585293790906753e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step1761",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1761 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 267.4577941894531,
        "th2": 267.73358154296875,
        "t1_in": 273.29400634765625,
        "rch": 17.27041848166613,
        "rr": 1.27586100170388,
        "t24": 5117066182.975906,
        "fdown": 467.3633117675781,
        "flx2": 0.0,
        "emissi": 0.9778155298147908,
        "df1": 0.44960019769020915,
        "snowh": 0.038037508726119995,
        "sncovr": 0.2052709015400025,
        "prcp": 0.00024957023561000824,
        "snowing": 1.0,
        "esd": 0.0034124997912607846,
        "etp": 2.5381805663880848e-05,
        "ribb": -0.9885614514350891,
        "eta_nosnow": 3.9349286511818614e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A1761_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08803750947371758,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2317674920850719,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 3.0674834401851285,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 7.38799196106435,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 61.63473379267768,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 273.168858656611,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 273.16806402555886,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 36.946458030856505,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 2.2113461150511426,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 6.6307229836615965e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 22.56584650263133,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 5.210146131337963e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 5.210146131337963e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step1824",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1824 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 268.0764465332031,
        "th2": 268.35284423828125,
        "t1_in": 275.89544677734375,
        "rch": 18.70340719224849,
        "rr": 1.2282820870842204,
        "t24": 5164575520.84535,
        "fdown": 549.1099395751953,
        "flx2": 0.0,
        "emissi": 0.9777742017984534,
        "df1": 0.4485843812296949,
        "snowh": 0.036144647747278214,
        "sncovr": 0.20645170152417336,
        "prcp": 8.177803465514444e-07,
        "snowing": 1.0,
        "esd": 0.003434411482886298,
        "etp": 3.5126514504215086e-05,
        "ribb": -1.2972400188446045,
        "eta_nosnow": 6.649146811415435e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A1824_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08614464849234421,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2266715413429448,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.013466237279988247,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.1955834256705,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 60.35390576741887,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 276.0526549393728,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 275.9289370950565,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 50.341594787251594,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 1.9629300892076031,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.885847343950834e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 33.71928245249002,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 7.2519286880087595e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 7.2519286880087595e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step1849",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1849 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 268.3482360839844,
        "th2": 268.6249084472656,
        "t1_in": 276.51885986328125,
        "rch": 19.069394410556942,
        "rr": 1.2246019119698222,
        "t24": 5185551832.669624,
        "fdown": 568.7386322021484,
        "flx2": 0.0,
        "emissi": 0.9778129411391985,
        "df1": 0.4485431404401194,
        "snowh": 0.03516868129372597,
        "sncovr": 0.20534486366955518,
        "prcp": 9.022944595926674e-07,
        "snowing": 1.0,
        "esd": 0.0034138713963338817,
        "etp": 3.81775777062247e-05,
        "ribb": -1.2985906600952148,
        "eta_nosnow": 7.853577710407442e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A1849_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08516868203879259,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2255238402836865,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.015526081843103764,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.650174348595035,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 60.08966686396573,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 276.68827496497534,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 276.5390782475416,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 53.16149793138656,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 2.6100203208569823,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 7.826147888626633e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 37.7944372060016,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 7.839569489318562e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 7.839569489318562e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step1874",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1874 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 268.5982971191406,
        "th2": 268.8752136230469,
        "t1_in": 276.7420654296875,
        "rch": 19.19112714602797,
        "rr": 1.2238060630802081,
        "t24": 5204907549.117991,
        "fdown": 573.1538696289062,
        "flx2": 0.0,
        "emissi": 0.9778566049107394,
        "df1": 0.4485876228495045,
        "snowh": 0.034208543598651886,
        "sncovr": 0.20409732784970258,
        "prcp": 8.361483310181939e-07,
        "snowing": 1.0,
        "esd": 0.003390752011910917,
        "etp": 3.974461855297218e-05,
        "ribb": -1.2473927736282349,
        "eta_nosnow": 8.703867832336212e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A1874_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08420854434371773,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2268182750560614,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.01434059277991789,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.627028865904352,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 60.48271139430635,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 276.901676708254,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 276.745397916633,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 53.741219627317896,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 2.856825028535823,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 8.566191989612663e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 40.28181695004487,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 8.111770443067335e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 8.111770443067335e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step1899",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1899 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 268.83026123046875,
        "th2": 269.107421875,
        "t1_in": 276.9125671386719,
        "rch": 19.335255313151507,
        "rr": 1.2227136537550076,
        "t24": 5222910890.002085,
        "fdown": 576.720947265625,
        "flx2": 0.0,
        "emissi": 0.9779028815711032,
        "df1": 0.4486243374860934,
        "snowh": 0.033275604248046875,
        "sncovr": 0.2027751380939995,
        "prcp": 7.172042160163983e-07,
        "snowing": 1.0,
        "esd": 0.0033662857022143623,
        "etp": 4.130371252087395e-05,
        "ribb": -1.177132487297058,
        "eta_nosnow": 9.472441203102419e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A1899_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08327560499311149,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2278716832915286,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.01220777411547979,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.569705230914828,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 60.81151000136049,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 277.0741284225618,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 276.9127770651018,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 54.11701913222315,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 3.0592874967693646,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 9.173275852381903e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 42.58900154967879,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 8.375366010215072e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 8.375366010215072e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step1924",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1924 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 269.0285949707031,
        "th2": 269.3059387207031,
        "t1_in": 276.3213806152344,
        "rch": 18.954079017058053,
        "rr": 1.22770351112757,
        "t24": 5238341092.917045,
        "fdown": 548.6803894042969,
        "flx2": 0.0,
        "emissi": 0.9779488793239925,
        "df1": 0.4488788946767402,
        "snowh": 0.03238306939601898,
        "sncovr": 0.2014609171200188,
        "prcp": 6.663678391305439e-07,
        "snowing": 1.0,
        "esd": 0.003342004027218293,
        "etp": 3.943685369395758e-05,
        "ribb": -1.0402679443359375,
        "eta_nosnow": 9.329601699206081e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A1924_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08238307014108304,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2341504673611183,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.010234481470363065,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 9.555037234998721,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 62.54820103858787,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 276.4102451573054,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 276.27792321355463,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 49.8537137093076,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 2.491449232744287,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 7.470612392036843e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 41.11688575212429,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 7.944984713512695e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 7.944984713512695e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step2089",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2089 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 268.9700927734375,
        "th2": 269.2474365234375,
        "t1_in": 268.6956787109375,
        "rch": 8.391757113705719,
        "rr": 1.7250902161801358,
        "t24": 5233786119.607903,
        "fdown": 289.4635181427002,
        "flx2": -140.23930286930408,
        "emissi": 0.9778638736219156,
        "df1": 0.4489576382077212,
        "snowh": 0.030685460194945335,
        "sncovr": 0.2038896504724078,
        "prcp": 0.000420507654780522,
        "snowing": 0.0,
        "esd": 0.0033869065814200014,
        "etp": 2.0403502611829307e-05,
        "ribb": 0.0,
        "eta_nosnow": 4.315231497781378e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A2089_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.0806854609438087,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.3843663528329206,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.4867285760643085,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 8.42503804509666,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 103.10028015309818,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 274.851675059134,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 274.7809347429996,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 36.426814262732094,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 10.874165017365762,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 3.260619195611922e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 20.364914875540634,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 4.160063015938737e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 4.160063015938737e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step2114",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2114 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 268.55841064453125,
        "th2": 268.8353271484375,
        "t1_in": 266.2958679199219,
        "rch": 0.4690393569455854,
        "rr": 10.79801407366544,
        "t24": 5201816551.506579,
        "fdown": 236.2884383201599,
        "flx2": -24.213451524701668,
        "emissi": 0.977478372523371,
        "df1": 0.4465652254348971,
        "snowh": 0.032493770122528076,
        "sncovr": 0.21490396307194037,
        "prcp": 7.260405254783109e-05,
        "snowing": 0.0,
        "esd": 0.0035921430681626855,
        "etp": 6.179493757822258e-08,
        "ribb": 0.749049186706543,
        "eta_nosnow": 1.3497527142035953e-08,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A2114_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08249377086826414,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.068834761960185,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.6928898935265049,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -5.338886215103386,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 286.70693342497367,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 265.81458701581164,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 265.81458701581164,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -13.14319681421252,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.06408506938678218,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.3279976983343206e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.3279976983343206e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step26",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 26 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.714111328125,
        "th2": 264.98712158203125,
        "t1_in": 264.19610595703125,
        "rch": 13.687830684095433,
        "rr": 1.3042378506051444,
        "t24": 4910303914.25537,
        "fdown": 271.2093200683594,
        "flx2": 0.0,
        "emissi": 0.9849884706179115,
        "df1": 0.4909357825395728,
        "snowh": 6.265289266593754e-05,
        "sncovr": 0.00032981949957555656,
        "prcp": 1.200106544274604e-05,
        "snowing": 1.0,
        "esd": 4.933989214983113e-06,
        "etp": -7.36691718419817e-07,
        "ribb": 0.029060401022434235,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A26_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.0500626536378767,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.5493123926270032,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.013092194050348227,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.14379570542039846,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 144.46915926090185,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 264.19918167723114,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 264.19918167723114,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 11.75968815750446,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -1.8425459266396589,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -7.36691718419817e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 7.36691718419817e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step2847",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2847 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.8333740234375,
        "th2": 265.1064147949219,
        "t1_in": 263.3333435058594,
        "rch": 0.5963846226421105,
        "rr": 7.896895592887509,
        "t24": 4919158930.793048,
        "fdown": 251.47598266601562,
        "flx2": 0.0,
        "emissi": 0.9773411546083614,
        "df1": 0.4541799186610361,
        "snowh": 0.03318041190505028,
        "sncovr": 0.21882447332697563,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0036658388562500477,
        "etp": 3.419697477964523e-08,
        "ribb": 0.5358104109764099,
        "eta_nosnow": 7.46211209620754e-09,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A2847_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08318041265010834,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.1593752490797424,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -4.457572506392024,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 308.12265378240426,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 263.26987657273827,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 263.26987657273827,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -13.629898543537385,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.03575614962382184,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 7.483134995531738e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 7.483134995531738e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step2880",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2880 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.7868957519531,
        "th2": 265.0599060058594,
        "t1_in": 263.30059814453125,
        "rch": 0.5442248474416398,
        "rr": 8.553929679274123,
        "t24": 4915706589.120108,
        "fdown": 252.1864776611328,
        "flx2": 0.0,
        "emissi": 0.9773411770992989,
        "df1": 0.45427332297960193,
        "snowh": 0.03317866101861,
        "sncovr": 0.21882383072902312,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0036658267490565777,
        "etp": 3.905357029324398e-08,
        "ribb": 0.5315546989440918,
        "eta_nosnow": 8.52135425256614e-09,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A2880_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08317866176366806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.173170848765882,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -4.320028432456176,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 311.7123680940208,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 263.2923388137898,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 263.2923388137898,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -13.15330746513925,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.04083311460917573,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 8.545851855212828e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 8.545851855212828e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step328",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 328 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 266.8771057128906,
        "th2": 267.1522521972656,
        "t1_in": 271.5361328125,
        "rch": 22.72746765452386,
        "rr": 1.1870572326861066,
        "t24": 5072771219.516592,
        "fdown": 477.5541229248047,
        "flx2": 0.0,
        "emissi": 0.9836268011486163,
        "df1": 0.4827894408161397,
        "snowh": 0.007400842849165201,
        "sncovr": 0.03923464557835188,
        "prcp": 7.14849193172995e-06,
        "snowing": 1.0,
        "esd": 0.0005980000132766325,
        "etp": 2.7977718208833934e-05,
        "ribb": -0.21435068547725677,
        "eta_nosnow": 4.240545109793444e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A328_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.05740084359429945,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.3117574073192158,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.07014036713145211,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 6.95081277651473,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 82.49042200645661,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 271.6343269782292,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 271.6343269782292,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 59.180477322449256,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 13.295975510385887,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.0976958580146013e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.0976958580146013e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step364",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 364 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 267.3176574707031,
        "th2": 267.5932312011719,
        "t1_in": 272.3958740234375,
        "rch": 22.97072328375942,
        "rr": 1.1860645998474295,
        "t24": 5106350092.587517,
        "fdown": 497.05682373046875,
        "flx2": 0.0,
        "emissi": 0.9834587635155759,
        "df1": 0.48112369441523706,
        "snowh": 0.008181992918252945,
        "sncovr": 0.0440357188457946,
        "prcp": 8.220598829211667e-06,
        "snowing": 1.0,
        "esd": 0.0006727515137836587,
        "etp": 3.2524038184321044e-05,
        "ribb": -0.23841558396816254,
        "eta_nosnow": 4.925428177377372e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A364_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.05818199366339559,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.3035184760250487,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.08791703608685952,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 7.4410247559183045,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 80.42775555958683,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 272.48285645272506,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 272.48285645272506,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 62.00433092549032,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 15.829222956252492,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.4322194012146494e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.4322194012146494e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step397",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 397 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 267.46044921875,
        "th2": 267.7361755371094,
        "t1_in": 272.70318603515625,
        "rch": 22.776008144431238,
        "rr": 1.1881782213904222,
        "t24": 5117269372.611448,
        "fdown": 497.86814880371094,
        "flx2": 0.0,
        "emissi": 0.9832748920127781,
        "df1": 0.47965882041325825,
        "snowh": 0.009015229530632496,
        "sncovr": 0.049289188207118695,
        "prcp": 1.107180469261948e-05,
        "snowing": 1.0,
        "esd": 0.0007549528381897958,
        "etp": 3.241596137756816e-05,
        "ribb": -0.26001566648483276,
        "eta_nosnow": 4.904918241867946e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A397_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.059015230275803195,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.3003372029391893,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.12224605132923316,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 7.4845008717630455,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 79.69777823608635,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 272.7313557783245,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 272.7313557783245,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 59.90419375415001,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 16.184210839711298,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.5977564212536477e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.5977564212536477e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step51",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 51 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.6050720214844,
        "th2": 264.87799072265625,
        "t1_in": 264.1499328613281,
        "rch": 10.349196232590808,
        "rr": 1.4167371731827876,
        "t24": 4902218430.566047,
        "fdown": 273.02410888671875,
        "flx2": 0.0,
        "emissi": 0.9848021558070801,
        "df1": 0.49051296093205643,
        "snowh": 0.001084580784663558,
        "sncovr": 0.005653097633327997,
        "prcp": 8.533049549441785e-05,
        "snowing": 1.0,
        "esd": 8.478196841117266e-05,
        "etp": -6.473796409117417e-07,
        "ribb": 0.0395466685295105,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A51_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.051084581530817276,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.6548845370795633,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.0817912486159269,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.2604835523600773,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 172.26611039871165,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 264.1463233102526,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 264.1463233102526,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 10.545448909904911,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -1.620300523324198,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -6.473796409117417e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 6.473796409117417e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step519",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 519 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 267.6418762207031,
        "th2": 267.9178161621094,
        "t1_in": 271.4065246582031,
        "rch": 19.617367139683033,
        "rr": 1.2492228680354958,
        "t24": 5131168338.633834,
        "fdown": 414.1601257324219,
        "flx2": 0.0,
        "emissi": 0.9825914826822462,
        "df1": 0.47538998621763395,
        "snowh": 0.012081330642104149,
        "sncovr": 0.06881516109885122,
        "prcp": 0.00029488836298696697,
        "snowing": 1.0,
        "esd": 0.0010642694545133357,
        "etp": 2.199805338222707e-05,
        "ribb": -0.2491612434387207,
        "eta_nosnow": 3.3189568732203053e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A519_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06208133139011956,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.312470024479926,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 2.3379780374969528,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 4.8701173962047815,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 83.3179845590202,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 271.11474665254,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 271.11474665254,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 34.24158193053367,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 12.013549197821296,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.5137995873590848e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.5137995873590848e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step679",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 679 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 266.4090576171875,
        "th2": 266.6838684082031,
        "t1_in": 266.7725524902344,
        "rch": 9.840968901724938,
        "rr": 1.4349564764578662,
        "t24": 5037278296.402685,
        "fdown": 279.9432634115219,
        "flx2": 0.0,
        "emissi": 0.98220348399459,
        "df1": 0.473927681991508,
        "snowh": 0.013881165534257889,
        "sncovr": 0.07990083335811693,
        "prcp": 3.504056439851411e-05,
        "snowing": 1.0,
        "esd": 0.0012426043395303418,
        "etp": 1.3199469988725476e-06,
        "ribb": -0.014354582875967026,
        "eta_nosnow": 1.9878044376356074e-07,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A679_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06388116627970378,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.525366833079934,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.026824259958855512,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.09448095992038993,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 140.40011758053538,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 266.75790199007184,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 266.75790199007184,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -3.5919578493197717,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.7558927678611889,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.0546486519846198e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.0546486519846198e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseA_step76",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 76 of case A, snow accumulating onto initially bare frozen ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.5255432128906,
        "th2": 264.79833984375,
        "t1_in": 264.076904296875,
        "rch": 8.22644844633965,
        "rr": 1.5208368556013179,
        "t24": 4896327510.070017,
        "fdown": 272.6068115234375,
        "flx2": 0.0,
        "emissi": 0.9845167303558036,
        "df1": 0.49020930569843213,
        "snowh": 0.0026703651528805494,
        "sncovr": 0.01380810719384784,
        "prcp": 7.423989882227033e-05,
        "snowing": 1.0,
        "esd": 0.00020789193520761513,
        "etp": -5.343008348312178e-07,
        "ribb": 0.050854817032814026,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_A76_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.05267036589889819,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.7439096747780858,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.07014434768513578,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.2347150231415624,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 195.76102960043468,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 264.0740483850281,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 264.0740483850281,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 8.58523045165396,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -1.3387136456860413,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -5.343008348312177e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 5.343008348312177e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step1",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.81134033203125,
        "th2": 265.08447265625,
        "t1_in": 263.0,
        "rch": 11.039300272720537,
        "rr": 1.3622763850412556,
        "t24": 4917522072.076789,
        "fdown": 173.4457550048828,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21504083602532403,
        "snowh": 0.29999998211860657,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.06000000238418579,
        "etp": -8.003809375277104e-06,
        "ribb": 0.034011732786893845,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B1_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.3499999828636646,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.040855087223694,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -4.389939157031206,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 10.744887939831523,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 260.52261495701777,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 260.52261495701777,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -1.5221113625226967,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -22.598115466344883,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -8.003809375277104e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 8.003809375277104e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step100",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 100 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.7906799316406,
        "th2": 265.0637512207031,
        "t1_in": 264.7860107421875,
        "rch": 10.258819424786383,
        "rr": 1.4007472862554484,
        "t24": 4915987604.776065,
        "fdown": 263.6443176275332,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21341115503282554,
        "snowh": 0.30376335978507996,
        "sncovr": 0.98,
        "prcp": 5.3555111662717536e-05,
        "snowing": 1.0,
        "esd": 0.06030664220457664,
        "etp": 1.8213744631308727e-07,
        "ribb": 0.01945704035460949,
        "eta_nosnow": 2.7651187174893626e-08,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B100_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.35376336053081514,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.0419804500708723,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.000526624175101853,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.06575653065825174,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 11.041295237947065,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 264.78206158424587,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 264.78206158424587,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 1.0687679994101875,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.5065231059872044,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.7849469738682552e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.7849469738682552e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step1612",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1612 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 275.2957458496094,
        "th2": 275.57965087890625,
        "t1_in": 273.3233337402344,
        "rch": 1.1169385045693754,
        "rr": 5.022980120145518,
        "t24": 5743782698.845811,
        "fdown": 340.5548858642578,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21154235889835754,
        "snowh": 0.30848824977874756,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.06072096899151802,
        "etp": 3.0350004667688822e-06,
        "ribb": 0.26228219270706177,
        "eta_nosnow": 1.6383804707627516e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B1612_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.3584882505238056,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1051796435200698,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 4.056057494616,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 27.70894603317987,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 277.8378620867433,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 273.335639338635,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 5.837013247611595,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 27.83240943627454,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 8.345550055854434e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 8.499222085684371,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.9743004574335046e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.9743004574335046e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step1637",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1637 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 275.6798400878906,
        "th2": 275.96417236328125,
        "t1_in": 273.6241455078125,
        "rch": 1.0488849713915678,
        "rr": 5.301796898836049,
        "t24": 5775904883.486098,
        "fdown": 386.8654327392578,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21356771600091162,
        "snowh": 0.3044896721839905,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.060493938624858856,
        "etp": 3.0028749992586438e-06,
        "ribb": 0.27968016266822815,
        "eta_nosnow": 1.809719943294202e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B1637_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.35448967292904854,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1083380628324875,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 12.11956635203085,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 28.541012651291524,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 285.4187090559428,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 273.6358408786153,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 6.140230004911013,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 72.5319471746293,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 2.1748709797490043e-07,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 8.418695714507498,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.942817499273471e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.942817499273471e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step1816",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1816 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 277.1918640136719,
        "th2": 277.4779052734375,
        "t1_in": 274.9055480957031,
        "rch": 0.841175687252457,
        "rr": 6.451387662379336,
        "t24": 5903667855.589271,
        "fdown": 584.6944885253906,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.2284806810120927,
        "snowh": 0.25674816966056824,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.054353997111320496,
        "etp": 2.8303884110337475e-06,
        "ribb": 0.3497317135334015,
        "eta_nosnow": 1.9686088246112113e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B1816_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.3067481704056263,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1372548351475071,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 47.6807340019822,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 36.2343633455782,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 317.52510536866174,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 274.907254172599,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 8.129198950471807,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 262.9065673583701,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 7.883255393054577e-07,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 7.948269032568048,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.7737806428130724e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.7737806428130724e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step1841",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1841 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 277.2937927246094,
        "th2": 277.57989501953125,
        "t1_in": 274.927734375,
        "rch": 0.8106177220108658,
        "rr": 6.662949398056377,
        "t24": 5912356209.440992,
        "fdown": 587.8560028076172,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.23062031365063018,
        "snowh": 0.24898476898670197,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.05315843224525452,
        "etp": 2.7275421896022567e-06,
        "ribb": 0.3680911660194397,
        "eta_nosnow": 1.9228713265196918e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B1841_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.29898476973176,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1428123886975934,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 48.457390251186276,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 37.71296101593258,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 318.04358054426615,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 274.9277857895529,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 8.372429761126721,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 266.0078648793455,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 7.976247822469131e-07,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 7.660747532395414,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.6729913458102114e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.6729913458102114e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step1866",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1866 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 277.3777770996094,
        "th2": 277.66400146484375,
        "t1_in": 274.90826416015625,
        "rch": 0.7784935604057894,
        "rr": 6.901806584011033,
        "t24": 5919522199.936567,
        "fdown": 584.4489593505859,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.2327739379923982,
        "snowh": 0.24135594069957733,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.05196269601583481,
        "etp": 2.607519274486839e-06,
        "ribb": 0.3907901346683502,
        "eta_nosnow": 1.8635029765609804e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B1866_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.2913559414446354,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1486937334901388,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 48.06556703972176,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 39.27808861980626,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 317.50972615736697,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 274.9066451558317,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 8.590408143334859,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 262.8101347519574,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 7.880363860628406e-07,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 7.3249063747493794,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.555368888997102e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.555368888997102e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step2122",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2122 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 277.27166748046875,
        "th2": 277.557861328125,
        "t1_in": 262.7182922363281,
        "rch": 0.3497408759242021,
        "rr": 14.119355304835356,
        "t24": 5910469450.016999,
        "fdown": 242.70480728149414,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.2523563635343791,
        "snowh": 0.19721251726150513,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.045533597469329834,
        "etp": -1.2178610323198167e-06,
        "ribb": 2.7153196334838867,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B2122_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.2472125180065632,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2067200216932479,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -15.3494019410992,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 54.75891492610097,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 262.4313633423511,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 262.4313633423511,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -2.513983849563007,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": -0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step26",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 26 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.8386535644531,
        "th2": 265.1117858886719,
        "t1_in": 264.7561340332031,
        "rch": 15.594263494151622,
        "rr": 1.258127592299795,
        "t24": 4919551202.772385,
        "fdown": 262.0423278808594,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21504307706639877,
        "snowh": 0.30001741647720337,
        "sncovr": 0.98,
        "prcp": 1.1722505405487027e-05,
        "snowing": 1.0,
        "esd": 0.06000409275294522,
        "etp": 5.051071490987363e-07,
        "ribb": 0.011769433505833149,
        "eta_nosnow": 7.668229015669557e-08,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B26_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.35001741722240903,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.0313145557379602,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": -0.0020372088812932176,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -0.014675135629588807,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 8.235728159083514,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 264.7685956420138,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 264.7685956420138,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 1.086586638924892,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 1.404699815464073,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 4.950050061167616e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 4.950050061167616e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step2880",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2880 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 274.5351867675781,
        "th2": 274.8185119628906,
        "t1_in": 256.04461669921875,
        "rch": 0.34562363692959647,
        "rr": 13.887329411525565,
        "t24": 5680571897.104703,
        "fdown": 208.31295776367188,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.2525818657587315,
        "snowh": 0.19706536829471588,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.045533597469329834,
        "etp": -1.5541043223582414e-06,
        "ribb": 3.2695465087890625,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B2880_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.24706536903977394,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2129943674759684,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -20.375599739710882,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 56.420952130425384,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 256.04450233726726,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 256.04450233726726,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -9.04719633054446,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": -0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step435",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 435 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 266.554931640625,
        "th2": 266.8298034667969,
        "t1_in": 271.3992614746094,
        "rch": 20.197459768005576,
        "rr": 1.234186042585374,
        "t24": 5048320140.139172,
        "fdown": 441.20701599121094,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21066424632437186,
        "snowh": 0.3098119795322418,
        "sncovr": 0.98,
        "prcp": 0.00030910407076589763,
        "snowing": 1.0,
        "esd": 0.06073277816207325,
        "etp": 2.353874977937634e-05,
        "ribb": -0.29727229475975037,
        "eta_nosnow": 3.5751254638866377e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B435_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.3598119802806809,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.023487556188403,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 3.15352876324714,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 4.2529816041224295,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 6.186150513236884,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 270.63745141127583,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 270.63745141127583,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 4.249174218305019,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 65.46119641382595,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.3067974783788812e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.3067974783788812e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step463",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 463 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 266.8583984375,
        "th2": 267.1335754394531,
        "t1_in": 271.67205810546875,
        "rch": 19.89877615507019,
        "rr": 1.2088132984784785,
        "t24": 5071349025.576865,
        "fdown": 466.73509216308594,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21037003629806494,
        "snowh": 0.310437947511673,
        "sncovr": 0.98,
        "prcp": 2.943338404293172e-05,
        "snowing": 1.0,
        "esd": 0.06077174469831549,
        "etp": 2.8533639524628142e-05,
        "ribb": -0.3155849277973175,
        "eta_nosnow": 4.333923203568766e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B463_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.3604379482570452,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.0242643005810252,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.29838291044647614,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 4.955158746397455,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 6.391766807297152,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 271.61478129558895,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 271.61478129558895,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 4.781336381307465,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 79.3519786962462,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.7962966734135578e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.7962966734135578e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step492",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 492 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 266.94970703125,
        "th2": 267.2249755859375,
        "t1_in": 270.99835205078125,
        "rch": 19.43902851928679,
        "rr": 1.21145871627138,
        "t24": 5078293464.507362,
        "fdown": 445.9703063964844,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21017096794401535,
        "snowh": 0.3108033537864685,
        "sncovr": 0.98,
        "prcp": 6.192137334437575e-06,
        "snowing": 1.0,
        "esd": 0.06078648194671296,
        "etp": 2.724967194861807e-05,
        "ribb": -0.25719109177589417,
        "eta_nosnow": 4.1387340074800365e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B492_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.3608033545315922,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.0247354025056221,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.05279692715245676,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 4.320389822986458,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 6.517180707485293,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 271.0819562615801,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 271.0819562615801,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 4.430632038763667,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 75.78125965735151,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.670467850964571e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.670467850964571e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step51",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 51 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.8194580078125,
        "th2": 265.09259033203125,
        "t1_in": 264.8497009277344,
        "rch": 13.57661316043778,
        "rr": 1.3080474406407976,
        "t24": 4918125077.754083,
        "fdown": 264.257080078125,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.214619750222465,
        "snowh": 0.3009808361530304,
        "sncovr": 0.98,
        "prcp": 8.666866779094562e-05,
        "snowing": 1.0,
        "esd": 0.06008230149754608,
        "etp": 4.244947343670679e-07,
        "ribb": 0.010922453366219997,
        "eta_nosnow": 6.444433288196374e-08,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B51_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.35098083689918164,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.0344327207712185,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.005520065198926449,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.0939951942937598,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 9.05580556283049,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 264.8497609014917,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 264.8497609014917,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 1.1311022737217717,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 1.180517201824382,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 4.1600483967972654e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 4.1600483967972654e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step517",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 517 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 266.9682312011719,
        "th2": 267.2435302734375,
        "t1_in": 270.7884216308594,
        "rch": 19.087643997265932,
        "rr": 1.2707790295158508,
        "t24": 5079703182.678276,
        "fdown": 410.3553161621094,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.21008102214191518,
        "snowh": 0.31090250611305237,
        "sncovr": 0.98,
        "prcp": 0.0005081301205791533,
        "snowing": 1.0,
        "esd": 0.0607801862066105,
        "etp": 2.309344245243127e-05,
        "ribb": -0.24778249859809875,
        "eta_nosnow": 3.507195036899704e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B517_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.3609025068634865,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.023997972825773,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 4.088069952654152,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 3.029308621013091,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 6.323844469716688,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 269.8456360508011,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 269.8456360508011,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 3.684604874204658,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 64.2227831933186,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.2631573603382646e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.2631573603382646e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step561",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 561 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 267.4836730957031,
        "th2": 267.7594909667969,
        "t1_in": 270.32318115234375,
        "rch": 17.28979184353776,
        "rr": 1.240058178977217,
        "t24": 5119046956.016613,
        "fdown": 413.01417541503906,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.2097057840309104,
        "snowh": 0.31172868609428406,
        "sncovr": 0.98,
        "prcp": 1.3551401025324594e-05,
        "snowing": 1.0,
        "esd": 0.06083413213492795,
        "etp": 2.3250661990431415e-05,
        "ribb": -0.21240268647670746,
        "eta_nosnow": 3.5315022628014096e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B561_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.36172868683947973,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.0270393116580951,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.08103743189371321,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 3.5960844139299626,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 7.12698014504871,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 270.8822675984362,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 270.8822675984362,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 4.2342523807607195,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 64.66003170744781,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.2785648750622787e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.2785648750622787e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseB_step658",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 658 of case B, a 60 kg/m2 pack at the 0.98 cover cap under warm advection; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 269.36480712890625,
        "th2": 269.642578125,
        "t1_in": 264.0404968261719,
        "rch": 0.6784305211879328,
        "rr": 7.204462815968587,
        "t24": 5264576196.022855,
        "fdown": 255.68093872070312,
        "flx2": 0.0,
        "emissi": 0.9507000002861022,
        "df1": 0.2098019167122622,
        "snowh": 0.3112076222896576,
        "sncovr": 0.98,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.060759976506233215,
        "etp": -2.472614329758008e-07,
        "ribb": 0.737175464630127,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_B658_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.36120762303471565,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1188353261320916,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -5.6731339241488765,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 31.34087342777594,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 263.6961309154277,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 263.6961309154277,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -0.021788074866287265,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -0.1872283880380363,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -6.631262371097331e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 6.631262371097331e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.81134033203125,
        "th2": 265.08447265625,
        "t1_in": 271.0,
        "rch": 24.171723128403073,
        "rr": 1.1696753809977403,
        "t24": 4917522072.076789,
        "fdown": 173.4457550048828,
        "flx2": 0.0,
        "emissi": 0.9749635201505887,
        "df1": 0.3236200250879231,
        "snowh": 0.02499999850988388,
        "sncovr": 0.2867568586410364,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.005000000353902578,
        "etp": -9.073732284151229e-06,
        "ribb": -0.09935659170150757,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07499999925494194,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1526163870135047,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -2.4137973790929212,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 41.51165726767326,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 263.66899138754906,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 263.66899138754906,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -35.94774990602985,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -23.549447626460747,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -9.073732284151229e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 9.073732284151229e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1564",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1564 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 280.3654479980469,
        "th2": 280.654541015625,
        "t1_in": 269.89031982421875,
        "rch": 0.37163220906755945,
        "rr": 14.11196639635289,
        "t24": 6178712135.466858,
        "fdown": 285.0992202758789,
        "flx2": 0.0,
        "emissi": 0.9759984122883805,
        "df1": 0.3424737504307019,
        "snowh": 0.02148446999490261,
        "sncovr": 0.25718852393208325,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.00440554553642869,
        "etp": -1.1737129238439888e-07,
        "ribb": 2.0598607063293457,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1564_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07148447073996067,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.913512939107557,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -10.772115164377432,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 247.2613122061187,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 270.10773456323943,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 270.10773456323943,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -2.6977599356894637,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -0.22383330786930294,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -8.656869091465959e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 8.656869091465959e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step169",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 169 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 265.3818054199219,
        "th2": 265.655517578125,
        "t1_in": 267.9590759277344,
        "rch": 18.697330616090444,
        "rr": 1.230289135404694,
        "t24": 4960033129.225212,
        "fdown": 321.5060920715332,
        "flx2": 0.0,
        "emissi": 0.974282830066498,
        "df1": 0.322154344443349,
        "snowh": 0.03003288432955742,
        "sncovr": 0.30620513880906053,
        "prcp": 8.57914419611916e-05,
        "snowing": 1.0,
        "esd": 0.00540340179586049,
        "etp": 8.801694017127854e-06,
        "ribb": -0.15734097361564636,
        "eta_nosnow": 3.8559063568772953e-07,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C169_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08003288507564835,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1749881836309082,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.4656529282166382,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 1.906720106742728,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 47.596785947607046,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 267.99019416622883,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 267.99019416622883,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -16.140569823300254,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 8.29627027001302,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.6951239382695124e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.6951239382695124e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1785",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1785 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 283.6958923339844,
        "th2": 283.9887390136719,
        "t1_in": 288.3206481933594,
        "rch": 15.023376223741387,
        "rr": 1.3362371032469005,
        "t24": 6477571128.587273,
        "fdown": 702.6154327392578,
        "flx2": 0.0,
        "emissi": 0.9771556996267998,
        "df1": 0.33606626403856266,
        "snowh": 0.01713281124830246,
        "sncovr": 0.2241231849202019,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0037659858353435993,
        "etp": 9.021460844400702e-05,
        "ribb": -1.0483665466308594,
        "eta_nosnow": 4.6538407060638215e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1785_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06713281199336052,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2493670165374218,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 9.992647667809402,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 67.56129314700664,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 289.1462863730724,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 288.34277368071645,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 87.16242266370655,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 19.527937604554523,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.8554535545890624e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 147.52658029315043,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.0219185370799793e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.0219185370799793e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1810",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1810 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 283.8733215332031,
        "th2": 284.1663513183594,
        "t1_in": 288.81524658203125,
        "rch": 15.313417978474906,
        "rr": 1.330552772764531,
        "t24": 6493791157.739107,
        "fdown": 718.247802734375,
        "flx2": 0.0,
        "emissi": 0.9773738740479959,
        "df1": 0.33547796324782053,
        "snowh": 0.016465021297335625,
        "sncovr": 0.21788963257664729,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0036482352297753096,
        "etp": 9.391979001533476e-05,
        "ribb": -1.094099521636963,
        "eta_nosnow": 4.8551430046183725e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1810_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06646502204239368,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2477231555424388,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.305858531245011,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 67.18009607572209,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 289.6149474625017,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 288.8332593952433,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 89.05213690189238,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 19.161538371637448,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.745588717132668e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 152.8829549205388,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.0464148538117157e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.0464148538117157e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1838",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1838 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 284.03369140625,
        "th2": 284.326904296875,
        "t1_in": 289.15423583984375,
        "rch": 15.452521365061221,
        "rr": 1.3282029109069096,
        "t24": 6508477867.739452,
        "fdown": 725.6940002441406,
        "flx2": 0.0,
        "emissi": 0.9776146356285391,
        "df1": 0.33459829872222424,
        "snowh": 0.015743093565106392,
        "sncovr": 0.2110107330869384,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0035192957147955894,
        "etp": 9.571321505251155e-05,
        "ribb": -1.123907208442688,
        "eta_nosnow": 4.953214270225491e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1838_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06574309431016445,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2479760894608554,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.454012445768184,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 67.30923031717353,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 289.90694391067495,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 289.1608321106209,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 90.21857855186228,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 18.35007233021784,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.502270563783461e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 154.89604208554968,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.0196515674338252e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.0196515674338252e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1863",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1863 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 284.1417541503906,
        "th2": 284.43505859375,
        "t1_in": 289.26007080078125,
        "rch": 15.415594599948575,
        "rr": 1.3294240627123453,
        "t24": 6518388318.21039,
        "fdown": 723.308349609375,
        "flx2": 0.0,
        "emissi": 0.9778221987368004,
        "df1": 0.3337482285875504,
        "snowh": 0.015130738727748394,
        "sncovr": 0.20508036098903404,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0034089668188244104,
        "etp": 9.518296109426191e-05,
        "ribb": -1.1328190565109253,
        "eta_nosnow": 4.925784688369406e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1863_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06513073947280645,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2500398008240827,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.406172812580927,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 67.92374531246213,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 289.96810504471614,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 289.26076994858494,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 90.23365623230654,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 17.360859591342717,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.205655049877876e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 153.17127222801446,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.9520156021216417e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.9520156021216417e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1888",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1888 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 284.2215881347656,
        "th2": 284.5149841308594,
        "t1_in": 289.169677734375,
        "rch": 15.238216746244657,
        "rr": 1.3335981228534215,
        "t24": 6525717170.960758,
        "fdown": 712.3860168457031,
        "flx2": 0.0,
        "emissi": 0.9780195571145142,
        "df1": 0.3327876932068125,
        "snowh": 0.01455513946712017,
        "sncovr": 0.19944155250189521,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0033047660253942013,
        "etp": 9.27920119722102e-05,
        "ribb": -1.1141648292541504,
        "eta_nosnow": 4.79848527601248e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1888_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06455514021217823,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.253674788192391,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.163191091093351,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 68.96042438586649,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 289.82412905951,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 289.16088334733814,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 89.26087678052652,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 16.18745557936674,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 4.85380976892556e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 148.44874243676483,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.850658292751205e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.850658292751205e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step1978",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1978 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 284.218505859375,
        "th2": 284.5119323730469,
        "t1_in": 287.2949523925781,
        "rch": 13.035887732259798,
        "rr": 1.3901321533996351,
        "t24": 6525434099.848776,
        "fdown": 605.6522369384766,
        "flx2": 0.0,
        "emissi": 0.9786096755730825,
        "df1": 0.33134979337767323,
        "snowh": 0.012845908291637897,
        "sncovr": 0.1825810320054171,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.002997202565893531,
        "etp": 6.797763130622496e-05,
        "ribb": -0.8852062225341797,
        "eta_nosnow": 3.49733383509879e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C1978_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06284590903669596,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2909464024265247,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 7.768453059074025,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 79.47853409699049,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 287.7466425540326,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 287.2600513118683,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 74.27583379217995,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 11.102191201261746,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 3.3289928639465504e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 106.62259902402022,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.2411426077174303e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.2411426077174303e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step2003",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2003 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 284.1286926269531,
        "th2": 284.4220886230469,
        "t1_in": 286.3112487792969,
        "rch": 11.791893773237696,
        "rr": 1.4309169520167437,
        "t24": 6517189843.011195,
        "fdown": 559.2235260009766,
        "flx2": 0.0,
        "emissi": 0.9787330044403066,
        "df1": 0.33170351243202156,
        "snowh": 0.012480990961194038,
        "sncovr": 0.17905735152491842,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0029336686711758375,
        "etp": 5.6739688763608485e-05,
        "ribb": -0.7210168242454529,
        "eta_nosnow": 2.9166337046394722e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C2003_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.0624809917062521,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.3146329260792355,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 6.66036055765484,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 86.11803148111026,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 286.7013880367403,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 286.2669097330707,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 66.66548699375095,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 9.492202216958688,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 2.8462375463144494e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 88.63550210464014,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.0159658396359909e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.0159658396359909e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step2104",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2104 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 283.14385986328125,
        "th2": 283.43634033203125,
        "t1_in": 276.0175476074219,
        "rch": 0.19900485623708075,
        "rr": 26.269965288358012,
        "t24": 6427300312.151368,
        "fdown": 323.6805419921875,
        "flx2": 0.0,
        "emissi": 0.978966053780629,
        "df1": 0.3325704432121893,
        "snowh": 0.011629151180386543,
        "sncovr": 0.17239880166574628,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.002814299426972866,
        "etp": 1.8496345043826507e-07,
        "ribb": 3.6810078620910645,
        "eta_nosnow": 1.0114561487384763e-07,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C2104_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.0616291519254446,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.032224788654019,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -6.374210210236316,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 283.87674835415385,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 275.8781415999386,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 275.7970575572843,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 4.223115767058959,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.2995958489189814,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 3.188747720751855e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 3.188747720751855e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step2119",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2119 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 282.89190673828125,
        "th2": 283.1841125488281,
        "t1_in": 272.833984375,
        "rch": 0.18665321686948294,
        "rr": 27.870334858741828,
        "t24": 6404453718.242151,
        "fdown": 288.5576477050781,
        "flx2": 0.0,
        "emissi": 0.9789660222979083,
        "df1": 0.3326147652399378,
        "snowh": 0.011586623266339302,
        "sncovr": 0.17239970117168413,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.002814315492287278,
        "etp": -3.6409878578684064e-07,
        "ribb": 5.321341514587402,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C2119_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06158662401139736,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.038191479542762,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -12.709278124265687,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 285.4779757474722,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 272.62433875257983,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 272.62433875257983,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -12.701990172854352,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -0.7674366589171709,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -3.000472328617137e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 3.000472328617137e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step2141",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2141 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 282.4830017089844,
        "th2": 282.7747802734375,
        "t1_in": 268.93988037109375,
        "rch": 0.179464089408718,
        "rr": 28.8258392220426,
        "t24": 6367504753.468692,
        "fdown": 248.99274063110352,
        "flx2": 0.0,
        "emissi": 0.9789648186780183,
        "df1": 0.33264493891002533,
        "snowh": 0.011589097790420055,
        "sncovr": 0.1724340902973429,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.002814929699525237,
        "etp": -7.240182910358626e-07,
        "ribb": 7.189432144165039,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C2141_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.061589098535478115,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.044040997704286,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -19.885536979246236,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 286.90414208944054,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 268.83101045249964,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 268.83101045249964,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -32.24739735524595,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -1.526006121409339,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -5.966249896344281e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 5.966249896344281e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step2166",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2166 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 282.04949951171875,
        "th2": 282.3408203125,
        "t1_in": 268.21258544921875,
        "rch": 0.17975707796828244,
        "rr": 28.652959054407727,
        "t24": 6328508003.499507,
        "fdown": 242.67832946777344,
        "flx2": 0.0,
        "emissi": 0.9789630124228376,
        "df1": 0.3335732176554511,
        "snowh": 0.01159284170717001,
        "sncovr": 0.1724856975671265,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0028158514760434628,
        "etp": -7.331343468469688e-07,
        "ribb": 7.311386585235596,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C2166_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.06159284245222807,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.0514907302052254,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -20.77476933790243,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 288.95134053919264,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 268.2079244189253,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 268.2079244189253,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -35.70991749976396,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -1.545131451223151,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -6.040984394731738e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 6.040984394731738e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step26",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 26 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 265.10174560546875,
        "th2": 265.3751525878906,
        "t1_in": 266.05389404296875,
        "rch": 21.301257685454704,
        "rr": 1.1953786587529054,
        "t24": 4939128778.2553625,
        "fdown": 270.18603515625,
        "flx2": 0.0,
        "emissi": 0.9749573351257507,
        "df1": 0.3241662298508379,
        "snowh": 0.02504994161427021,
        "sncovr": 0.2869335735641815,
        "prcp": 2.2222642655833624e-05,
        "snowing": 1.0,
        "esd": 0.005003620404772331,
        "etp": 4.771822991635361e-06,
        "ribb": -0.02095392718911171,
        "eta_nosnow": 2.0893286216251633e-07,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C26_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07504994235960208,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1696315626495608,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.04456138993882419,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -0.05174097122956886,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 46.139785040680536,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 266.05796185080965,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 266.05796185080965,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -25.6656839951116,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 4.24743181871548,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.3691962234056574e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.3691962234056574e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step268",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 268 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 267.8174743652344,
        "th2": 268.0935974121094,
        "t1_in": 273.2484130859375,
        "rch": 23.941058296530606,
        "rr": 1.1778485388204638,
        "t24": 5144647705.526234,
        "fdown": 480.2809753417969,
        "flx2": 0.0,
        "emissi": 0.974184173044172,
        "df1": 0.3215856099844185,
        "snowh": 0.03075668215751648,
        "sncovr": 0.3090239097234353,
        "prcp": 8.484566933475435e-06,
        "snowing": 1.0,
        "esd": 0.005462722387173316,
        "etp": 3.516816002647259e-05,
        "ribb": -0.2340828776359558,
        "eta_nosnow": 2.155281196788827e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C268_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.08075668290265847,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.1412164675073497,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0970427174620836,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 5.962745740752134,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 38.40230308868552,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 273.55241716459153,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 273.5139880248689,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 6.270770815467601,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.531971981810436,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 1.595118386238189e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 34.48048921970693,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.0867802309159993e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.0867802309159993e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step2880",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 2880 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 280.45721435546875,
        "th2": 280.7467956542969,
        "t1_in": 266.5170593261719,
        "rch": 0.18315059849540258,
        "rr": 27.68764557597633,
        "t24": 6186805519.968868,
        "fdown": 238.95335388183594,
        "flx2": 0.0,
        "emissi": 0.9789155503285378,
        "df1": 0.3509901020437974,
        "snowh": 0.011691033840179443,
        "sncovr": 0.17384175685001746,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.0028400917071849108,
        "etp": -6.992301097236038e-07,
        "ribb": 7.198464393615723,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C2880_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.0616910345852375,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 2.1219627717926435,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -20.295324580179567,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 305.377530988348,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 266.5171266345389,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 266.5171266345389,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -32.227462409015544,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -1.471457795655027,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -5.75193996747296e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 5.75193996747296e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step380",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 380 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 270.2742614746094,
        "th2": 270.55291748046875,
        "t1_in": 277.9803161621094,
        "rch": 24.436855200130342,
        "rr": 1.1785200015051904,
        "t24": 5336036077.65127,
        "fdown": 629.7510375976562,
        "flx2": 0.0,
        "emissi": 0.9744475705157608,
        "df1": 0.3225338362782828,
        "snowh": 0.02874927408993244,
        "sncovr": 0.30149827075390057,
        "prcp": 1.631580062166904e-06,
        "snowing": 1.0,
        "esd": 0.005304833874108039,
        "etp": 5.9707423276272806e-05,
        "ribb": -0.3783034086227417,
        "eta_nosnow": 1.129982145529561e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C380_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07874927483500391,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.142215340629788,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.026478833161911464,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 9.41087192981054,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 38.67393591644348,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 278.7207087809979,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 278.214324627469,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 25.700775528338635,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 15.094061371845726,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 4.5259554338367997e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 70.68502319074497,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.800168486896744e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.800168486896744e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step405",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 405 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 271.71661376953125,
        "th2": 271.99676513671875,
        "t1_in": 279.9307861328125,
        "rch": 24.428257245360726,
        "rr": 1.1813420640371115,
        "t24": 5450856821.179574,
        "fdown": 674.1453399658203,
        "flx2": 0.0,
        "emissi": 0.9746205161550239,
        "df1": 0.3229134941330746,
        "snowh": 0.027913276106119156,
        "sncovr": 0.2965569687945533,
        "prcp": 1.5638310407181307e-30,
        "snowing": 0.0,
        "esd": 0.005202005617320538,
        "etp": 7.031491503100308e-05,
        "ribb": -0.4243001937866211,
        "eta_nosnow": 1.6120216530367172e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C405_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07791327685117722,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.14361723822378,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 5.418264680401369e-26,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 10.132207439130946,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 39.05516692479585,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 280.60436429925903,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 279.94878251017286,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 33.19562171150692,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 19.906595745357663,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.968994226494053e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 87.37270452077749,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.0852378062640848e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.0852378062640848e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step434",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 434 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 272.97418212890625,
        "th2": 273.255615234375,
        "t1_in": 280.4862976074219,
        "rch": 23.177361364995193,
        "rr": 1.1938343033926853,
        "t24": 5552470934.36531,
        "fdown": 660.12451171875,
        "flx2": 0.0,
        "emissi": 0.9748563828369575,
        "df1": 0.3233093876999732,
        "snowh": 0.026858793571591377,
        "sncovr": 0.2898179234936723,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.005062823183834553,
        "etp": 7.206908655936295e-05,
        "ribb": -0.4386773705482483,
        "eta_nosnow": 1.9504420908138125e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C434_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07685879431664944,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.152025591551741,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 9.612785306169041,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 41.34172839086789,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 281.18185759191493,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 280.5072263014543,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 36.041427971614816,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 20.041145463956383,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 6.009338969702064e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 93.75304087578746,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.0886913014720297e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.0886913014720297e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step459",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 459 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 273.8331298828125,
        "th2": 274.1154479980469,
        "t1_in": 280.7311706542969,
        "rch": 22.17919227130096,
        "rr": 1.204513088176007,
        "t24": 5622687690.895818,
        "fdown": 648.4131317138672,
        "flx2": 0.0,
        "emissi": 0.9750616753812028,
        "df1": 0.323561075195399,
        "snowh": 0.02596842683851719,
        "sncovr": 0.2839524246268551,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.004942660219967365,
        "etp": 7.253970052076579e-05,
        "ribb": -0.4455168545246124,
        "eta_nosnow": 2.403675165213497e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C459_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07596842758357525,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.159428471859375,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 9.07654768006375,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 43.354862257767834,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 281.40117975317077,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 280.73589555040195,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 37.46616463436178,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 19.367840769126417,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.8074485064846824e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 101.33769728878858,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.059782384457739e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.059782384457739e-08,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step56",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 56 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 265.0768737792969,
        "th2": 265.35028076171875,
        "t1_in": 266.2160949707031,
        "rch": 17.609447882866146,
        "rr": 1.2438031938988847,
        "t24": 4937275484.302442,
        "fdown": 271.8406982421875,
        "flx2": 0.0,
        "emissi": 0.974789774044584,
        "df1": 0.32362248109238834,
        "snowh": 0.02628016471862793,
        "sncovr": 0.29172103106936875,
        "prcp": 8.560367132304236e-05,
        "snowing": 1.0,
        "esd": 0.005102005787279379,
        "etp": 3.32641538623722e-06,
        "ribb": -0.04758032038807869,
        "eta_nosnow": 1.456417201652578e-07,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C56_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07628016546474292,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.193700012825094,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.20538031360870956,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 0.02554948209645008,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 52.68640348842557,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 266.22168328348897,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 266.22168328348897,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -24.514802517034944,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 3.0041810467011434,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 9.703853262381344e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 9.703853262381344e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step708",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 708 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 280.16912841796875,
        "th2": 280.4581604003906,
        "t1_in": 265.233642578125,
        "rch": 0.3512651717722595,
        "rr": 14.839571080279075,
        "t24": 6161424289.064176,
        "fdown": 229.32296980917454,
        "flx2": 0.0,
        "emissi": 0.9760702364271161,
        "df1": 0.32411775418417577,
        "snowh": 0.02129247412085533,
        "sncovr": 0.2551364065212315,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.00436509819701314,
        "etp": -1.1956925710999214e-06,
        "ribb": 2.7869832515716553,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C708_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07129247486591339,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.8721731047444778,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -20.964910442560726,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 237.32291179797383,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 265.2143268777221,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 265.2143268777221,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -31.328440818959685,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -2.2861261396218873,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -8.844020548809765e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 8.844020548809765e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseC_step733",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 733 of case C, a thin pack melting while the soil thaws and refreezes; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW. This step takes the FROST ADJUSTMENT (etp <= 0, ribb >= 0.1, fdown > 150 W/m^2).",
      "parameter_overrides": {
        "sfctmp": 280.1464538574219,
        "th2": 280.43548583984375,
        "t1_in": 265.2377014160156,
        "rch": 0.35202178393504047,
        "rr": 14.806598004078086,
        "t24": 6159429913.314859,
        "fdown": 229.542236328125,
        "flx2": 0.0,
        "emissi": 0.9760678843381686,
        "df1": 0.324817031763049,
        "snowh": 0.021298784762620926,
        "sncovr": 0.25520360903512096,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 0.004366421140730381,
        "etp": -1.1796552604245776e-06,
        "ribb": 2.7745721340179443,
        "eta_nosnow": 0.0,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_C733_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.07129878550767899,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.8740410622001689,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -20.908912661807854,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 237.83119289502648,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 265.2389769448648,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 265.2389769448648,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -31.280953737343047,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": -2.2552734965082526,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": -8.724590564678248e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 8.724590564678248e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseD_step1",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 1 of case D, a trace pack melting out into bare ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.8114318847656,
        "th2": 265.0842590332031,
        "t1_in": 271.0,
        "rch": 24.346953680413037,
        "rr": 1.1702995797172129,
        "t24": 4917528872.583518,
        "fdown": 154.25025939941406,
        "flx2": 0.0,
        "emissi": 0.9848831994276912,
        "df1": 0.33509353226838906,
        "snowh": 0.0002500000118743628,
        "sncovr": 0.0033375665622663586,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 5.0000002374872565e-05,
        "etp": 1.1497574492365082e-05,
        "ribb": -0.10248859971761703,
        "eta_nosnow": 5.034268065768349e-07,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_D1_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.05025000075693242,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2340390325899158,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -4.038842223763704,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 63.65861686445711,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 262.90190014862435,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 262.90190014862435,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -60.67093274038161,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 1.363466405927002,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 3.83739201728843e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 3.83739201728843e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseD_step26",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 26 of case D, a trace pack melting out into bare ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.311279296875,
        "th2": 264.5836181640625,
        "t1_in": 261.08050537109375,
        "rch": 6.00900810696326,
        "rr": 1.6861075466908808,
        "t24": 4880482804.439932,
        "fdown": 164.4716796875,
        "flx2": 0.0,
        "emissi": 0.9848832855350358,
        "df1": 0.3367205908892153,
        "snowh": 0.0002498149697203189,
        "sncovr": 0.0033351063534242664,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 4.9963087803917006e-05,
        "etp": 3.194596380044882e-06,
        "ribb": 0.11259123682975769,
        "eta_nosnow": 1.3987933326638368e-07,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_D26_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.05024981571477838,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.6613740326646012,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -10.542107645707446,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 179.89373688477153,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 261.02665625536906,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 261.02665625536906,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -73.53162866696695,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.378823186728959,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 1.065431868371385e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 1.065431868371385e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseD_step392",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 392 of case D, a trace pack melting out into bare ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 271.5202331542969,
        "th2": 271.7999267578125,
        "t1_in": 282.0552673339844,
        "rch": 25.845930935353174,
        "rr": 1.1729361504855782,
        "t24": 5435115675.551669,
        "fdown": 703.2776641845703,
        "flx2": 0.0,
        "emissi": 0.9848927932859329,
        "df1": 0.33697274436191305,
        "snowh": 0.00021633169671986252,
        "sncovr": 0.003063456438819556,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 4.588760566548444e-05,
        "etp": 9.457892430004255e-05,
        "ribb": -0.5189628601074219,
        "eta_nosnow": 4.740317375705098e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_D392_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.05021633244177792,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2213518892139625,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 13.008207934836172,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 60.13287385214139,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 282.19657085321376,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 282.1061051446816,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 70.08504465830262,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.4913401743446446,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 1.4732838810933874e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 12.639174558800802,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.8973841462359275e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.8973841462359275e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseD_step417",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 417 of case D, a trace pack melting out into bare ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 272.80828857421875,
        "th2": 273.0893249511719,
        "t1_in": 283.07513427734375,
        "rch": 25.36220175781067,
        "rr": 1.1787560622966984,
        "t24": 5538985705.963761,
        "fdown": 704.7557373046875,
        "flx2": 0.0,
        "emissi": 0.984901336555294,
        "df1": 0.33510004220683587,
        "snowh": 0.00019741823780350387,
        "sncovr": 0.002819363128271135,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 4.2226442019455135e-05,
        "etp": 9.863084135826184e-05,
        "ribb": -0.5215075016021729,
        "eta_nosnow": 5.536259613563387e-06,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_D417_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.050197418982861564,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2232966474653062,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 12.977411624334415,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 60.66119056548063,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 283.2075862235692,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 283.1070103613335,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 76.40349775702356,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.9488362605686529,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 2.8450862385866655e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 14.5941033947817,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 2.7807615743584313e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 2.7807615743584313e-10,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseD_step51",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 51 of case D, a trace pack melting out into bare ground; SNOPAC takes its sub-freezing block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 264.0509033203125,
        "th2": 264.3229675292969,
        "t1_in": 260.4454650878906,
        "rch": 3.7939356495036782,
        "rr": 2.08347928808376,
        "t24": 4861279931.945205,
        "fdown": 164.1351776123047,
        "flx2": 0.0,
        "emissi": 0.9848833125714427,
        "df1": 0.3385706828827671,
        "snowh": 0.0002497566747479141,
        "sncovr": 0.0033343338849722848,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 4.995149720343761e-05,
        "etp": 1.8440696595486895e-06,
        "ribb": 0.14966470003128052,
        "eta_nosnow": 8.074843291879109e-08,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_D51_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.050249757419805974,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.852385850924065,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": -13.47561953198638,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 231.84895145134567,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 260.43398841500215,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 260.43398841500215,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": -77.92898198189627,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 0.21867940128195512,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 6.1487439520825005e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 6.1487439520825005e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseD_step521",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 521 of case D, a trace pack melting out into bare ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 275.6548156738281,
        "th2": 275.9388427734375,
        "t1_in": 282.3080749511719,
        "rch": 21.34772757874045,
        "rr": 1.2190887982485665,
        "t24": 5773807973.445439,
        "fdown": 610.1920013427734,
        "flx2": 0.0,
        "emissi": 0.9849717743036369,
        "df1": 0.3276035112707624,
        "snowh": 5.456982398754917e-05,
        "sncovr": 0.0008068568553057931,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 1.2073031030013226e-05,
        "etp": 8.595124004671721e-05,
        "ribb": -0.4564281105995178,
        "eta_nosnow": 1.9888171418797078e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_D521_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.05005457056904561,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2514883174560578,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 9.371986360486694,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 68.35710802707531,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 282.37092199128585,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 282.27871277137297,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 68.5151794175859,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 1.8543776378792742,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.560352737269188e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 49.896444885610215,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 6.93503472537276e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 6.93503472537276e-11,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    },
    {
      "id": "cold_caseD_step553",
      "description": "Reference: WRF 4.8 em_scm_xy COLD-SEASON single-column run, data/eqwefic/noahcold_scm, dumped by ctessum-claude/WRF branch earthsciml-instrumented-noahcold (commit 4695cee3) and replayed through the real64 (-fdefault-real-8) kernels/noah_driver at ESM_DT = 1e-6 s. SNOPAC's closure is evaluated on the INPUT column -- t12 and everything it selects are formed before the pack or the soil are advanced -- so the only dt dependence reaching these quantities is through df1 and the incoming pack, and 1e-6 s is the right reference step, the same choice the soil-heat surface closure makes. THE MELT RATE IS REFERENCED BEFORE ITS LIMITER: `ex` is asserted against the replay's `sno_ex_raw`, the rate SNOPAC forms from the energy residual, and NOT against the post-limiter `sno_ex` or against a snow-amount difference. That publisher exists because differencing the pack would put this quantity in exactly the cancellation-versus-clamping bind that FORTRAN_BUGS N97 documents for the frozen-soil sink; referencing the pre-limiter rate avoids it entirely. The two limiters themselves are PROJECTIONS of the state after a step, not parts of the rate, and are reported as the indicators `pack_exhausted` and `melt_limited` rather than folded in. Step 553 of case D, a trace pack melting out into bare ground; SNOPAC takes its MELT block. SNOPAC's EVAPORATION SPLIT is computed here, not supplied: the inputs are PENMAN's etp (epsca rch/lvs from the replay's PENMAN publishers), the dumped ribb and, where etp > 0, EVAPO's snow-free eta_nosnow, recovered from the replay's published edir + ec + ett (which SNOPAC weighted by 1 - sncovr and SFLX converted with LVH2O). etanrg, esnow_rate and esnow2_rate are asserted against the replay's own SNOPAC publishers sno_etanrg, sno_esnow1 and sno_esnow2/dt, and dew against SFLX's DEW.",
      "parameter_overrides": {
        "sfctmp": 276.70697021484375,
        "th2": 276.9920349121094,
        "t1_in": 281.5694580078125,
        "rch": 19.221761267303865,
        "rr": 1.2461169692245413,
        "t24": 5862466802.128997,
        "fdown": 553.6766204833984,
        "flx2": 0.0,
        "emissi": 0.9849970854198699,
        "df1": 0.32654227478349934,
        "snowh": 5.6008470892265905e-06,
        "sncovr": 8.368240136436e-05,
        "prcp": 0.0,
        "snowing": 0.0,
        "esd": 1.2517150480562123e-06,
        "etp": 7.564385073978943e-05,
        "ribb": -0.38847872614860535,
        "eta_nosnow": 2.052103864059951e-05,
        "dt_pack": 1e-06
      },
      "expression_template_imports": [
        {
          "ref": "./tests/sno_D553_inputs.esm"
        }
      ],
      "time_span": {
        "start": 0.0,
        "end": 1.0
      },
      "assertions": [
        {
          "variable": "dsoil",
          "time": 0.0,
          "expected": 0.05000000074505806,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "dtot",
          "time": 0.0,
          "expected": 0.050005601592147286,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "denom",
          "time": 0.0,
          "expected": 1.2726269395049303,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "flx1",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "t12a",
          "time": 0.0,
          "expected": 7.53173925990087,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12b",
          "time": 0.0,
          "expected": 74.19447977201042,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "t12",
          "time": 0.0,
          "expected": 281.6482805135263,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "melting",
          "time": 0.0,
          "expected": 1.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "t1",
          "time": 0.0,
          "expected": 281.563297708391,
          "tolerance": {
            "rel": 1e-09
          }
        },
        {
          "variable": "ssoil",
          "time": 0.0,
          "expected": 61.49246521656105,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "flx3",
          "time": 0.0,
          "expected": 1.9675242867021225,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "ex",
          "time": 0.0,
          "expected": 5.8996230485820764e-09,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-18
          }
        },
        {
          "variable": "frost_adjusted",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "abs": 0.0,
            "rel": 0.0
          }
        },
        {
          "variable": "etanrg",
          "time": 0.0,
          "expected": 51.33673686560147,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-12
          }
        },
        {
          "variable": "esnow_rate",
          "time": 0.0,
          "expected": 6.3300590783528e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "esnow2_rate",
          "time": 0.0,
          "expected": 6.3300590783528e-12,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        },
        {
          "variable": "dew",
          "time": 0.0,
          "expected": 0.0,
          "tolerance": {
            "rel": 1e-09,
            "abs": 1e-20
          }
        }
      ]
    }
  ]
}